Belarus 80.1 Series Скачать руководство пользователя страница 170

Страница: 170 / 381

80-0000010B OM

170

In the hydraulic lift linkage safety valve, retarding valve and filter valve have the following

intended use:

- safety valve, installed in the distributor, designated to prevent the HLL from overloading

by way of limiting the pressure in the range from 18 to 20 MPa (in case the pressure in the HLL

increases above the specified level, the oil flow is drained into the tank through the safety valve);

- retarding valve, installed directly in the cylinder, is designated to reduce lowering speed of

the mounted equipment to avoid damage to the working bodies by the ground.

- filter valve, installed in the filter body, is designated to limit drain pressure in the range

from 0,3 to 0,4 MPa (in case filter element is dirty oil flow through the filter valve is drained into

the tank bypassing the filter).

HLL hydraulic circuit diagram with the distributor

РП70-890 is shown in figure 3.15.2.

1 - distributor РП70-890.1, 2 – retarding valve, 3 - cylinder, 4 - spool, 5 – back-flow

valve, 6 – safety valve, 7 – hydraulic system filter, 8 – filter valve, 9 - pump, 10 - tank.

Figure 3.15.2 – HLL hydraulic circuit diagram with the distributor РП70-890.1 in-

stalled

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды