Belarus 80.1 Series Скачать руководство пользователя страница 242

Страница: 242 / 381

80-0000010B OM

242

4.3 Safety measures during tractor operation

4.3.1 General safety measures during tractor operation

Do not operate the tractor in a closed room without proper ventilation. Exhaust gas

may result in lethal outcome.

Tractor start-up and operation with the tractor hood open is not allowed.

It is forbidden to open the tractor hood when the engine is running.

Do not start the engine when staying outside the operator's seat. When starting the

engine and manipulating the controls, always stay inside the cab in the operator's seat.

Start the tractor by way of towing only in extreme emergency cases and only on a

tractor that has undergone a full 30-hours run-in.

Before starting the engine, the parking brake shall be engaged, the rear and side

PTO shall be disengaged, the GB range and gear shifting lever shall be in the Neutral po-

sition.

During tractor start there shall be no people under, in front of or behind the tractor,

as well as between the tractor and the coupled implement.

Before setting on the move, warn people around including those operating the cou-

pled implements using the horn, make sure the parking brake is off and start moving slow-

ly.

Use safety belts (supplied against order) when driving on public roads.

Passenger staying in the cab during tractor operation is strictly forbidden. (Passen-

ger may stay in the cab only if an additional seat is installed and transport operations are

carried out).

Do not leave the tractor on the move.

While performing transport operations observe traffic regulations, adopted in the

country where the tractor is operated.

Transport operations can be performed by drivers who have at least two years' expe-

rience of operating a tractor and who have passed exams on traffic rules.

Drive the tractor on slippery roads with automatic DL engaged only at a speed not

higher than 10 km/h.

To use the tractor for transport operations, do the following:

- set the track for front wheels (1520±20) and rear wheels (1800±20) mm;

- check operation of brakes; interlock the brake pedals, check and if necessary ad-

just the brakes for simultaneous of operation;

- check operation of the parking brake;

- check the condition of devices for light and sound annunciation

- coupled implements shall have rigid hitches and moreover shall be linked with a

safety chain or a cable;

- never move downhill with the gear disengaged. Move uphill and downhill at the

same gear;

It is forbidden to operate with a trailer without independent brakes, if its weight ex-

ceeds a half of the total actual weight of the tractor. The faster you move and the more

weight you tow, the longer the safety distance shall be.

It is prohibited to drive the tractor on public roads with the wheels twinned!

Transporting people in trailers is forbidden.

Before getting down to work with a trailer, turn the compressor on, check the condi-

tion of the trailer brake pneumatic drive and air pressure in the system. Remove the fail-

ures detected. Make sure to connect the pneumatic drive of trailer brake. Make sure the

parking brake is engaged while attaching the trailer connecting head to the tractor con-

necting head.

Do not work under raised agricultural implements. Do not leave implements uplifted

when stopping for a long time.

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды