manualshive.com logo in svg

Belarus 80.1 Series, Руководство по эксплуатации

Операционное и сервисное руководство для серии Belarus 80.1 доступно для бесплатного скачивания с manualshive.com. Этот manual предоставляет всю необходимую информацию для правильной эксплуатации и обслуживания продукта. Скачайте его сейчас, чтобы быть уверенными в работе вашего оборудования.

Поделиться
Скачать
background image

80-0000010B OM 

 

371

8. Tractor storage 

 

8.1 General instructions

 

 

ATTENTION:  RULES  ON  LONG-TERM  STORAGE,  PRESERVATION,  REPRE-

SERVATION  AND  DEPRESERVATION  OF  THE  ENGINE  INSTALLED  ON  THE  TRAC-
TOR  ARE  GIVEN  IN  THE  ENGINE  OPERATION  MANUAL,  WHICH  YOU  CAN  PUR-
CHASE  FROM  YOUR  DEALER!  RULES  ON  INTER-SHIFT  AND  SHORT-TERM  STOR-
AGE OF THE ENGINE INSTALLED ON THE TRACTOR, ARE GIVEN IN THIS SECTION 
8 «TRACTOR STORAGE». 

 Tractors shall be stored according to requirements of GOST 7751-85 in the indoor 

area or under a shed. 

If  indoors  premises  are  not  available,  tractors  may  be  stored  on  special  outdoor 

sites,  with  obligatory  preservation,  sealing  and  dismounting  of  components  that  require 
ware-housing. 

Put the tractors in the inter-shift storage, if their operation is interrupted for up to 10 

days, short-term storage if duration of idle interval is from 10 days to 2 months, and long-
term storage if interruption of use lasts for over 2 months. Prepare the tractor for inter-shift 
and short-term storage immediately after finishing work, and for long-term storage not later 
than ten days after finishing work. 

 

 

8.2 Requirements for inter-shift storage of tractors 

 

The  tractor  may  be  stored  on  storage  yards  and  inter-shift  storage  grounds  or  di-

rectly on work execution sites. The tractor shall be cleaned off dust and dirt.  All openings 
through  which  precipitation  can  ingress  the  tractor’s  inner  cavities  including  the  engine 
shall be tightly closed with covers. Accumulator batteries shall be disengaged. 

 

8.3 Requirements for short-term tractor storage 

 

Put the tractor for storage as a complete unit without removing components and as-

sembly units from the tractor. Follow the instructions of subsection 8.2 “Requirements for 
inter-shift storage of tractors”. 

Accumulator batteries shall be turned off. Electrolyte level and density shall conform 

to  the  accumulator  battery  maintenance  requirements  listed  in  paragraph  6.4.3.2  of  sub-
section 6.4.3 “Technical maintenance every 250 hours of operation.” If tractors are stored 
at low temperatures or for a period exceeding one month, the batteries shall be dismount-
ed and sent to a warehouse. 

 

8.4 Requirements for outdoors long-term storage 

 

Before placing a tractor for storage, check it for technical condition. The tractor shall 

undergo a regular maintenance service. 

Maintenance services when preparing tractor for long-term storage include: 
- cleaning and washing; 
- dismounting and preparing for storage of tractor components subject to storage in 

specially equipped warehouses;  

- sealing of openings (after removal of components), gaps and cavities from ingress 

of moisture and dust;  

- preservation of tractor and its components, restoration of damaged paintwork; 
- putting the tractor on stands (plates); 
-  following  the  instructions  of  operation  manual  for  engine  243-0000100OM  (or 

243С/245С-0000100 OM, if your tractor is equipped with engine 243С) as regards prepar-
ing the engine for long-term storage. 

After operation the tractor shall be cleaned from dust, mud, oil leaks, vegetation and 

other remainders. Components where water is not allowed (generators, relays, etc.) shall be 

Содержание 80.1 Series






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Murray 40508x92G Instruction Book preview
40508x92G
Бренд: Murray Страницы: 52
SaMASZ PSV 161 Operating Manual preview
PSV 161
Бренд: SaMASZ Страницы: 29
LAMBORGHINI R3 EVO 85 Workshop Manual preview
R3 EVO 85
Бренд: LAMBORGHINI Страницы: 61
Winton WFL Series Owner'S Manual preview
WFL Series
Бренд: Winton Страницы: 40
McCulloch M185-107TC Instruction Manual preview
M185-107TC
Бренд: McCulloch Страницы: 108
Troy-Bilt ST 100 1989 Service And Repair Manual preview
ST 100 1989
Бренд: Troy-Bilt Страницы: 113
Bad Boy 4035H 2021 Operator'S Manual preview
4035H 2021
Бренд: Bad Boy Страницы: 128
FENDT Vario 900 Series Workshop Service Manual preview
Vario 900 Series
Бренд: FENDT Страницы: 51
Husqvarna YTA18542 / 96045005500 NO. 960 45 00-55 Operator'S Manual preview
YTA18542 / 96045005500 NO. 960 45 00-55
Бренд: Husqvarna Страницы: 64
Husqvarna YTH220TWIN Instruction Manual preview
YTH220TWIN
Бренд: Husqvarna Страницы: 88
FMS FCX24 Instruction Manual preview
FCX24
Бренд: FMS Страницы: 43
Valtra VALMET 6000 Service Manual preview
VALMET 6000
Бренд: Valtra Страницы: 15
Tecnoma VECTIS 1000 Adjustments, Use And Maintenance preview
VECTIS 1000
Бренд: Tecnoma Страницы: 133
New Holland T6020 DELTA Specifications preview
T6020 DELTA
Бренд: New Holland Страницы: 4
New Holland T4.105V Service Manual preview
T4.105V
Бренд: New Holland Страницы: 51
New Holland Workmaster 50 Operator'S Manual preview
Workmaster 50
Бренд: New Holland Страницы: 184
New Holland Workmaster 25 Tier 4B Operator'S Manual preview
Workmaster 25 Tier 4B
Бренд: New Holland Страницы: 198
New Holland Workmaster 25S Operator'S Manual preview
Workmaster 25S
Бренд: New Holland Страницы: 208

Бренды по названию

Популярные бренды

Загрузить еще бренды