Belarus 80.1 Series Скачать руководство пользователя страница 317

Страница: 317 / 381

80-0000010B OM

317

6.4.5.4 Operation 51. Change of oil in HLL tank

Note – The operation shall be performed on tractors with canopy frame or canopy

base on the basis of small cabin.

Before oil change, heat up the oil in the HLL to reach the normal operating tempera-

ture by starting the engine and setting any of the levers of hydraulic outlet control to the

“Uplift” position and keeping the lever in such position until the hydraulic system is heated.

To change oil in hydraulic system of RLL, do the following:

- put the tractor on a flat ground, raise the RLL links to their top position, brake the

tractor using the parking brake. The engine shall be stopped;

- unscrew the plug of oil filler opening 3 (Figure 6.4.41) and drain plug 5; drain the

oil from the oil tank into a special container for used oil;

- re-place drain plug 5 and fill the system with fresh oil up to the mark “П” on oil level

indicator 2. When using machines that require large oil extraction, fill oil to the level of up-

per mark “С”.

- re-place the plug of oil filler opening 3.

1 – oil tank; 2 – oil indicator; 3 – plug of oil filler opening; 4 – HLL pump; 5 – drain

plug.

Figure 6.4.41 – Change of oil in RLL hydraulic system

ATTENTION: THE OPERATION OF OIL CHANGE IN HLL SHALL BE PER-

FORMED ONLY WITH RETRACTED RODS OF HYDRAULIC CYLINDERS OF HLL AND
OF MACHINES COUPLED WITH THE TRACTOR!

WARNING: BE CAREFUL TO AVOID CONTACT WITH HOT OIL!

6.4.5.5 Operation 52. Change of oil in transmission

Before changing the oil, warm up the transmission to reach the normal operating

temperature, by means of driving the tractor.

To change oil in transmission, do the following:

- put the tractor on a flat horizontal surface. The engine shall be stopped. Engage

the parking brake and block the wheels against spontaneous movement with wheel chocks

at the front and back;

- unscrew drain plug 1 (Figure 6.4.42) from rear axle body and drain plug 2 from

gearbox body; drain oil into a special container for used oil; in case the tractor is equipped

with a creeper (hydraulic creeper), then also unscrew check plug 3 located on the left side

of GB body;

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды