Belarus 80.1 Series Скачать руководство пользователя страница 128

Страница: 128 / 381

80-0000010B OM

128

1 – friction discs; 2 – stop; 3 – body; 4 – pin; 5 – fork; 6 – link; 7 – stop; 8, 9 – pressure

discs; 10 – shaft; 11 – balls.

Figure 3.7.2 – Operation principle of the service brakes

3.7.2 Check/adjustment of service brakes control

3.7.2.1

Check the adjustment of the service brakes control.

Full travel of the right brake pedal when pressing with a force from 120 to 130 N

shall be within the limits from 105 to 115 mm, and the left pedal travel when pressed with

the same force shall be 5-20 mm less.

If right and left pedal travel does not correspond to the specified values, adjust the

service brakes control.

3.7.2.2 Before carrying out adjustment of the service brakes control place the tractor

on the level horizontal ground. The engine should be killed. Block the wheels against

movement in front and at the back by wheel chocks, which prevent spontaneous move-

ment of the tractor.

3.7.2.3

Carry out adjustment of the service brakes control in the following way:

- install pads A of the pedals (figure 3.7.3) in one plane with a precision from 2 to 3

mm (leveling of the pads by bending legs Б is allowed);

- unscrew locknuts 1of adjusting bolts 2 of the left and right brakes;

- with the help of adjusting bolts 2 adjust the service brakes so that, when a force

from 120 to 130 N is applied full travel of right pedal 4 would be within the limits from 105 to

115 mm, and travel of left pedal 3 would be 5…20 mm less than right pedal travel;

- tighten locknuts 1.

ATTENTION: IT IS OBLIGATORY TO CARRY OUT FINAL CHECK OF CORRECTNESS

OF THE SERVICE BRAKES CONTROL ADJUSTMENT. FINAL CHECK OF SERVICE

BRAKES CONTROL ADJUSTMENT IS CARRIED OUT BY BRAKING THE TRACTOR WITH

THE INTERLOCKED PEDALS. NONSIMULTANEITY OF WHEELS BRAKING START SHALL

NOT EXCEED 1 M (BY TYRE PRINT). LENGTH OF BRAKING SHALL NOT BE MORE THAN

6 M AT A SPEED FROM 17 TO 18 KM/H WITH A FORCE NOT MORE THAN 600 N. IF

THESE CONDITIONS ARE NOT FULFILLED, REPEAT ADJUSTMENT OF THE SERVICE

BRAKES CONTROL (CHANGE THE VALUE OF FULL PEDAL TRAVEL RATE, BUT ONLY

WITHIN THE LIMITS OF THE VALUES SPECIFIED IN SUBSECTION 3.7.3.1)!

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды