manualshive.com logo in svg

Belarus 80.1 Series, Руководство по эксплуатации

Операционное и сервисное руководство для серии Belarus 80.1 доступно для бесплатного скачивания с manualshive.com. Этот manual предоставляет всю необходимую информацию для правильной эксплуатации и обслуживания продукта. Скачайте его сейчас, чтобы быть уверенными в работе вашего оборудования.

Поделиться
Скачать
background image

80-0000010B OM 

 

372

preserved  with  protective  covers.  After  being  cleaned  and  washed,  the  tractor  shall  be 
purged with compressed air to remove moisture. Damaged paint shall be restored by apply-
ing paint coating or protective grease. 

The painting shall be performed in accordance with GOST 6572-91. 
In  case  of  long-term  outdoor  storage,  electrical  equipment,  components  made  of 

rubber, polymer and textile materials (hydraulic circuit hoses, etc.) and tools shall be dis-
mounted,  prepared  for  storage  and  sent  to  a  warehouse.    Parts  for  fastening  the  tractor 
dismounted  components  shall  be  installed  back  into  their  places.  Electrical  equipment 
(headlights, accumulator battery, etc.) shall be cleaned, purged with compressed air, the 
terminals shall be coated with protective grease. 

When preparing the tractor for long-term storage, it is required to carry out internal and 

outside  preservation  procedures  for  the  engine  according  to  the  engine  operation  manual. 
Grease all tractor units according to clause 3 of table 6.7.1 of the present operation manual. 
Drain oil and refill fresh oil with the required amount of additives up to the control level to the 
housings of transmission, FDA wheel gear groups, hydraulic systems of RLL, HSC and HPS. 
Run the tractor in for 10-15 minutes. Place accumulator batteries for long-term storage after 
conducting control-training cycle in accordance with GOST 9590-76. Open hinges, screw and 
threaded connections of the linkage mechanism, of the steering, splined surfaces of the PTO 
shaft end and of cardan shafts, protruding parts of cylinder rods and of the shock absorbers, 
mechanisms for adjusting the front and rear wheel treads shall be treated for preservation. 
The fuel tank neck, breather holes of the engine, of the transmission and of the hydraulic sys-
tems,  the  engine  exhaust  pipe,  the  air  cleaner  inlet  pipe,  the  respective  openings  after  the 
starter removal and other cavities through which precipitations can get into the internal cavi-
ties of the tractor components and assembly units, shall be tightly closed with covers, plastic 
film bags or with other special appliances. Set the control levers and pedals to a position that 
excludes arbitrary engagement of the components and assemblies of the tractor.  

Open  storage  of  unloaded  pneumatic  tires  on  tractors,  resting  on  plates,  is  allowed. 

Tire surface shall be covered with protective agent. Tire pressure shall be decreased to 70% 
of the standard in case of open and closed storage. It is required to clean exterior surfaces of 
the hydraulic system flexible hoses from mud and oil. Hoses may be kept on the tractor. In 
this case they shall be coated with protective substance or wrapped with insulating material 
(wax paper, polyethylene film, etc.). 

The hoods and cab doors shall be closed. 
Regularly, in cold season or at long-term storage, the cylinder mechanism, located in 

button 2 (figure 2.19.1) of door lock handle, shall be checked for lubrication by means if in-
jecting agents (HG5501, WD-40). 

Maintenance  during  storage  includes  checking  if  tractors  are  properly  placed  on 

stands or plates (absence of skewness), checking for completeness of a set, air pressure in 
tires, air tightness, state of anticorrosion coatings (protective grease, paint integrity, absence 
of corrosion), state of protective accessories (integrity and holding strength of cases and co-
vers). Detected defects shall be eliminated. 

Tractor technical maintenance when removing from storage includes taking the tractor 

off the stands, cleaning and if required depreservation of the tractor and its components, re-
moval of air-tight packoff, reinstallation of previously dismounted components, tools, check of 
operation and adjustments of tractor and its components including the engine in accordance 
with  the  engine  operation  manual  243-0000100  OM  (or  243С/245С-0000100  OM,  if  your 
tractor is equipped with engine 243С). 

Содержание 80.1 Series






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Claas ARES 547 Use And Maintenance preview
ARES 547
Бренд: Claas Страницы: 31
Kersten WKB 60 M-U 70 Original Operating Manual preview
WKB 60 M-U 70
Бренд: Kersten Страницы: 19
Craftsman 486.248476 Operator'S Manual preview
486.248476
Бренд: Craftsman Страницы: 24
Craftsman 917.99039 Operator'S Manual preview
917.99039
Бренд: Craftsman Страницы: 36
Craftsman 917.257571 Owner'S Manual preview
917.257571
Бренд: Craftsman Страницы: 28
Craftsman CMXGZBF7124441 Instruction Manual preview
CMXGZBF7124441
Бренд: Craftsman Страницы: 36
Craftsman 917.203930 Operator'S Manual preview
917.203930
Бренд: Craftsman Страницы: 72
Craftsman 917.257572 Owner'S Manual preview
917.257572
Бренд: Craftsman Страницы: 28
WALTERSCHEID GKN HOLHS Mounting And Operating Instructions preview
GKN HOLHS
Бренд: WALTERSCHEID Страницы: 20
Zetor 8621 Forterra turbo Operator'S Manual preview
8621 Forterra turbo
Бренд: Zetor Страницы: 315
Husqvarna LGTH24V54 Operator'S Manual preview
LGTH24V54
Бренд: Husqvarna Страницы: 72
wsm L2800 Workshop Manual preview
L2800
Бренд: wsm Страницы: 16
wsm ME8200 Workshop Manual preview
ME8200
Бренд: wsm Страницы: 543
NMC-WOLLARD MB-4 200-DF Operation, Maintenance And Parts Manual preview
MB-4 200-DF
Бренд: NMC-WOLLARD Страницы: 321
LS tractor LL4100 Operator'S Manual preview
LL4100
Бренд: LS tractor Страницы: 46
LS tractor LL2100 Operator'S Manual preview
LL2100
Бренд: LS tractor Страницы: 46
LS tractor LB3100 Operator'S Manual preview
LB3100
Бренд: LS tractor Страницы: 61
LS tractor LB1100 Series Operator'S Manual preview
LB1100 Series
Бренд: LS tractor Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды