Belarus 80.1 Series Скачать руководство пользователя страница 296 | Manualshive

Страница: 296 / 381

background image

80-0000010B OM

296

6.4.3 Technical maintenance every 250 hours of operation

6.4.3.1 General instructions

Perform the previous operations, as well as operations listed in this subsec-

tion 6.4.3.

6.4.3.2 Operation 23. Accumulator battery technical maintenance

The operation shall be carried out every 250 hours, but not less often than once in

three months.

To carry out technical maintenance of AB perform the following:

- unscrew two bolts М6 fastening the rear drop-off panel (in cabin behind operator’s

seat), open the panel;

- clean the batteries from dust and dirt;

- check the condition of terminals 2 (Figure 6.4.16) of outlet pins, which are located

under protective cases “A” (Figure 6.4.16), and ventilation holes in plugs 1. If necessary,
lubricate the terminals with technical petroleum jelly and clean out the ventilation holes;

- unscrew plugs 1of filler opening of accumulator batteries, and check for the follow-

ing:

1. Electrolyte level – if necessary, add distilled water so that the electrolyte level

is 10 to 15 mm above the protective grid, or at the level marked on the battery case.

2. Degree of battery discharge by electrolyte density – if necessary recharge the

battery. Discharge of the battery below 50 % in summer and 25% in winter is not allowed.

1 – plugs of filler holes; 2 – outlet pin terminal.

Figure 6.4.16 – Maintenance of accumulator batteries

6.4.3.3 Operation 24. Check/adjustment of gaps in steering joints

To check backlash and play in joints 5 (Figure 6.4.18) of steering link 2, it is neces-

sary to turn the steering wheel to one and the other side when the engine is running. In
case the steering wheel angular play is more than 25° as shown in figure 6.4.17, remove
the play in steering joints by performing the following actions:

- stop the engine;
- brake the tractor using the parking brake;
- remove locking wire 3 (Figure 6.4.18);
- tighten threaded plug 4 so as to remove the steering joint play;
- lock plug 4 with wire 3.
- start the engine and turn the steering wheel either side; if the steering wheel play

is more than 25°, i.e. the steering joint play cannot be eliminated by tightening of threaded
plugs 4, it is necessary to stop the engine, engage the parking brake, take joint to pieces
and replace worn-out parts. Assemble joint 5, and tighten plug 4 so that ball pin rotates
when torque of 6 to 12 Nꞏm is applied, and lock with wire 3.

«
...
294
295
296
297
298
...
»

Содержание 80.1 Series






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Бренд: Brinly Страницы: 60

Бренд: Land Pride Страницы: 38

Бренд: Kubota Страницы: 370

Бренд: Degelman Страницы: 35

Бренд: bergmann Страницы: 98

Бренд: Valtra Страницы: 51

FENDT 800 Vario SCR Series

Бренд: AGCO Страницы: 51

Бренд: Rev-A-Shelf Страницы: 2

Бренд: Husqvarna Страницы: 84

Бренд: Textron Страницы: 150

Бренд: TYM Страницы: 175

Бренд: GOLDONI Страницы: 42

Бренд: GOLDONI Страницы: 153

Бренд: GOLDONI Страницы: 186

Бренд: GOLDONI Страницы: 185

Бренд: GOLDONI Страницы: 181

Бренд: GreenTec Страницы: 12

Бренд: GreenTec Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды