Belarus 80.1 Series Скачать руководство пользователя страница 324

Страница: 324 / 381

80-0000010B OM

324

1, 5 – drain plug; 2, 3, 4 – level/fill plug;

Figure 6.4.49 – Change of oil on bodies of FDA with bevel gear groups

- with the help of a grease gun for liquid lubricants, fill the hollows of upper bevel

pairs with oil up to the bottom edge of opening 4.

- place level/fill plug 3 (Figure 6.4.50) back to its place.

1 – cover; 2 – bolt; 3 – grease gun for liquid lubricants; 4 – level/fill hole of upper

bevel pair housing.

Figure 6.4.50 – Oil removal from upper bevel pair body

6.4.5.11 Operation 58. Change of oil in FDA master drive body, intermediate sup-

port of FDA cardan drive, FDA wheel gear group bodies

Note: The operation shall be performed only on BELARUS-820 tractor

Before changing the oil, warm up the oil in the bodies of FDA and intermediate sup-

port to normal operating temperature by driving the tractor.

Then place the tractor on a flat horizontal platform. The engine shall be shut down.

Apply the parking brake and put wheel chocks in front of and behind the rear wheels to
prevent movement of the tractor.

To change oil in the body of intermediate support, do the following:

- unscrew level/fill plug 1 (Figure 6.4.51) and drain plug 2 from intermediate support

body, drain oil into a special container for used oil;

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Belarus 80.1 Series, Руководство по эксплуатации, Страница: 324 / 381

Результаты поиска

Содержание 80.1 Series

Отзывы: