Belarus 80.1 Series Скачать руководство пользователя страница 289

Страница: 289 / 381

80-0000010B OM

289

6.4.1.6 Operation 5. Check of tyre condition

Inspect the visual appearance and condition of the tyres for damage, stuck objects in

the tyres (nails, stones and etc.). If required, clean the tyres from foreign objects. If there are

damages in the tyres that reach to the cord or through, it is necessary to dismantle the tyre

and send it to a special repair shop for restoration. If there are damages in the tyres, which

cannot be repaired, replace the tyre. Direct the defective tyre for disposal.

6.4.1.7 Operation 6. Inspection of hydraulic system components

Inspect hydraulic system components, if there are condensation and downflows,

eliminate them by tightening the threaded connections. Replace hoses and high-pressure

hoses that have failed.

6.4.1.8 Operation 7. Check of wiring in engine compartment

Inspect the condition of electrical wiring, wire harnesses in the engine compartment

for chaffing, melting or destruction of the external insulation.

In case of detection of the faults listed above do the following:

- restore the damaged areas with PVC adhesive tape;

- eliminate the cause of the damage to the insulation (as a rule it is caused by wrong fas-

tening of electrical wiring).

6.4.1.9 Operation 8. Check / cleaning of engine water radiator

Check the cleanness of the hood mask grid and of engine water radiator core. If they are

contaminated, clean them with a soft brush, purge with compressed air. Direct the air flow per-

pendicular to the water radiator plane, from top downward.

In case of strong contamination of the water radiator, rinse it with hot water under the

pressure not more than 0.2 MPa and purge it with compressed air, or clean the core with the

washing device “Kärcher”. In this case, it is necessary to clean the radiator core both from the

side of hood mask and from the engine fan side.

USE OF ALKALINE SOLUTIONS AND AGGRESSIVE WASHING COMPOSITIONS IS

PROHIBITED.

6.4.1.10 Operation 9. Check of breaks functioning during tractor movement, opera-

bility of engine, steering, light/alarm devices

The following tractor operating parameters shall be ensured:

- the engine shall work steadily in all modes;

- controls, light and acoustic alarm devices shall be in good order;

- simultaneous braking of the right and left service brakes.

If the above conditions are not observed, make the required adjustments or repairs

to the corresponding tractor systems.

6.4.1.11 Operation 10. Condensate water drain from pneumatic system tank

To remove condensate from the tank 2 of the pneumatic system (figure 6.4.5), it is

necessary to pull drain valve ring 1 installed on the tank in the horizontal direction to any

side and hold it till condensate water is drained completely.

1 – ring; 2 – pneumatic system tank.

Figure 6.4.5 – Drain of condensate water from the pneumatic system tank

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды