Belarus 80.1 Series Скачать руководство пользователя страница 200

Страница: 200 / 381

80-0000010B OM

200

3.18 Electrical equipment

3.18.1 General information

Electric circuit diagram of connections of BELARUS-80.1/82.1/820 tractors is given in

Annex A and B.

Electric circuit diagram of connections of BELARUS -80.1/82.1 tractors with canopy

frame or canopy base on the base of small cabin is given in Annex C.

3.18.2 Operation principle of heating plugs pilot indicator-lamp

As a means of start-up facilitation, tractors BELARUS-80.1/82.1/820 use heating

plugs (HP), which are mounted in cylinder head. To control HP, the electrical equipment cir-

cuit is equipped with a heating plug unit (HPU) and a heating plug relay. The operator se-

lects the operation mode for heating plugs based on the temperature of the engine or the

ambient temperature.

The following modes are available for operation of control and testing system of heat-

ing plugs:

- engine start-up without activating the heating plugs;

engine start-up with activating the heating plugs;

- emergency modes;

1 Engine start-up without activating the heating plugs

Turn the key of the starter and instruments switch from position I (instruments On) in-

to position II (engine start-up) within less than 2 seconds. In this case, heating plugs are not

activated and the pilot lamp of HP (see figure 2.6.1 or figure 2.25.1) does not light up.

2 engine start-up with activating the heating plugs

Activate the heating plugs. To do this, after turning the key of the starter and instru-

ments switch from position 0 (Off) into position I (instruments On), wait for the heating

plugs to activate (approximately 2 seconds after setting the key into position I). In this

case:

- the pilot lamp of heating plugs operation lights up and glows in continuous mode in

the pilot lamp unit, which indicates the activation of heating plugs;

- when the pilot lamp of HP operation changes from continuous glowing mode to

≈ 1 Hz frequency flashing mode, start the engine by depressing the clutch pedal and turn-

ing the key of the starter and instruments switch from position I (instruments On) into posi-

tion II (engine start-up). After engine start, the pilot lamp of HP operation goes out, but the

heating plugs keep operating for 3 more minutes, and only then they deactivate;

- if no start-up attempt is made within the period of the HP pilot lamp working in ≈ 1

Hz frequency flashing mode, the heating plugs and HP pilot lamp deactivate.

3 Emergency modes

In emergency modes, when there is a fault in the heating plug system, the HP pilot

lamp, instead of working according to the algorithm described in paragraph 2, starts to

work according to one of the following patterns:

- flashing mode with a frequency of ≈ 2 Hz. If the heating plugs did not turn off after

practicing the full cycle of operation described in paragraph 2 (relay contacts may stick or

mechanical breakdown may occur), the pilot lamp turns on intermittently with a frequency

of ≈ 2 Hz until the voltage on the contacts is removed;

- flashing mode with a frequency of "one turn-on every 3 seconds." If during opera-

tion of the heating plugs unit in the "engine start-up with activating the heating plugs"

mode, no voltage is supplied to the HP, then the pilot lamp starts to operate in intermittent

mode "one turn-on every 3 seconds";

- with an increase in the supply voltage to the heating plugs unit (more than 16_V),

the HPU turns off. In this case, after more than 2 seconds after turning the key of the start-

er and instruments switch from position “0” (Off) to position “I” (instruments On), the HP

pilot lamp and heating plugs do not turn on.

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды