Belarus 80.1 Series Скачать руководство пользователя страница 272 | Manualshive

Страница: 272 / 381

background image

80-0000010B OM

272

ATTENTION: TO IMPROVE LONGITUDINAL STABILITY AND REDUCE LOAD ON

FRONT AXLE, THE TRACTOR COUPLED WITH THE LOADER CAN BE EQUIPPED WITH

REAR MOUNTED BALLAST WEIGHTS!

LOADER OPERATION ON THE SLOPE WITH MORE THAN 8° INCLINE IS FORBID-

DEN.

Tractor service brake control pedals shall be always interlocked during loader oper-

ation.

Avoid abrupt start, braking, sharp turns and long-term frictional slip of tyres during

tractor operation with the loader.

When driving the tractor with the loader on public roads, it is required to observe

traffic regulations.

Before starting the movement on public roads, it is required to raise the loader into

transport position and fix it properly.

There is hazard of spontaneous lowering of the loader. That is why before leaving

the cab, it is required to lower the loader in the bottom position and fix the hydraulic control
mechanism levers of the loader properly.

It is required to carry out mounting and dismounting of the loader only on a level

ground with hard surface.

If the housing of the tractor with loader is under voltage, the operator shall lower the

operating part in the lowermost position, stop the engine, switch the accumulator battery

off and leave the cab urgently without touching the loader housing metal parts.

Before starting loading-unloading operations, an operator shall carry out preparatory

inspection of the working place, and study the rules and methods of operation depending
on specific conditions.

It is forbidden to let third persons drive the tractor with loader.

Before starting the movement or engaging reverse gear, it is necessary to sound a

horn and make sure there are no people in the area of loader operation.

Exercise caution when moving on the territory of an enterprise (the maximum speed

shall be determined by the enterprise standards).

When driving the tractor with loader, it is required to watch over for upper obstacles

(wires, pipelines, arches etc.).

When filling the loader bucket, avoid striking against obstacles hidden under the

load.

Intake of bulk materials shall be carried out by slow cutting in a stock pile and simul-

taneous turning of the loader bucket.

An operator is not allowed to start operation on load handling in the following cases:

- the load weight is unknown;

- poor light in the operation area, poor visibility of the loads to be moved;
- the territory of the working area on which the loader operates, does not have

proper solid and smooth surface (asphalt, concrete, paving blocks etc.), or the ground is

not cleaned from snow and ice and is not sanded or covered with special agent in winter;

- slope of the working area, on which the loader is intended to operate, exceeds 8°.

Stop the loader operation in the following cases:

- tyre puncture or insufficient tyre pressure;

- failure in steering, hydraulic or braking systems is detected;

- there are extraneous noises and slap noises in the engine, chassis or loader oper-

ating parts.

«
...
270
271
272
273
274
...
»

Содержание 80.1 Series






























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 80.1 Series

Бренд: Zetor Страницы: 136

WEATHER-BRAKE 2145

Бренд: Femco Страницы: 6

Бренд: Sears Страницы: 24

Бренд: Pasquali Страницы: 130

Бренд: FENDT Страницы: 6

Бренд: GE Страницы: 28

Бренд: Still Страницы: 146

Бренд: SAME Страницы: 24

Бренд: Cub Cadet Страницы: 36

Бренд: Cub Cadet Страницы: 40

Бренд: MTZ Страницы: 202

Бренд: MTZ Страницы: 244

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды