Belarus 80.1 Series Скачать руководство пользователя страница 330

Страница: 330 / 381

80-0000010B OM

330

- unscrew plug 3 (Figure 6.4.59), located on the bolt that attaches the outlet fitting,

by 2..3 revolutions;

- bleed the system with the help of booster pump 1, and tighten the plug as soon as

fuel without air bubbles appears;

- unscrew plug 2 on fuel pump body (the location of air bleed plug is different for

fuel pumps of different type);

- bleed the system with the help of booster pump and tighten plug 2 as soon as fuel

without air bubbles appears.

1 – booster pump; 2 – plug; 3 – plug (for air bleeding).

Figure 6.4.59 – Removing air from fuel supply system of the engine with indecom-

posable fine fuel filter

6.4.5.18 Operation 65. Rinsing of oil pre-filter of the engine

To rinse the engine oil pre-filter 1 (Figure 6.4.60). do the following:

- loosen four clamps 2 of connecting hoses, and take out the filter from oil line 3, lo-

cated before the oil radiator of the engine;

ATTENTION: REMEMBER THE WAY THE FILTER WAS POSITIONED IN THE

OIL LINE. ARBITRARY INSTALLATION OF THE FILTER INTO THE OIL LINE IS NOT

ALLOWED!

- rinse the filter in diesel fuel and purge with compressed air in the direction indicat-

ed by the arrow on filter body;

- install the filter back to its place. When mounting the filter into the oil line, provide

for input of oil on the same side it was before filter removal;

- tighten the clamps of hoses with the torque from 3 to 3.5 N



1 – pre-filter of engine oil; 2 – clamp; 3 – oil line.

Figure 6.4.60 – Rinsing of oil pre-filter of the engine

Содержание 80.1 Series






























































































































































































































































































































































































Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды

Belarus 80.1 Series, Руководство по эксплуатации

Результаты поиска

Содержание 80.1 Series

Отзывы:

Похожие инструкции для 80.1 Series

Бренды по названию

Популярные бренды