Avaya G700 Скачать руководство пользователя страница 192

Страница: 192 / 808

Installing a new G700 with an S8300 using the Avaya Installation Wizard

192 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

2. Verify that the G700 media gateway has registered.

The

in the registered field signifies that the G700 media gateway has registered. If the

G700 should become unregistered, the

will become an

, but the IP address will remain

assigned to the G700 media gateway. If the G700 has never been registered, the IP
Address field will be blank.

If the G700 fails to register, two common causes are:

- The serial number added as the

Identifier

for the G700 is wrong. To check, log back into

the G700 gateway and type

show system

. Check the serial number that appears.

- There is no IP connection between the G700 and the S8300. To check, type

show mgc

and then

ping mgp

<controller_address>

To enable announcements, if necessary

Only if specifically requested by the customer or your planning documents,

at the SAT

prompt, type

enable announcement-board

<gateway_number>

where

<gateway_number>

is the number of the G700 media gateway you added.

is the virtual slot (for example,

2V9

means media gateway number 2, slot V9.

2. Press

Enter

to enable announcements.

The system displays the message

Command successfully completed

Saving Communication Manager translations

Save translations again after all Communication Manager administration is complete.

1. At the SAT prompt, type

save translation

Содержание G700









































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание G700

Отзывы:

Avaya G700, Установка и обновление, Страница: 192 / 808

Результаты поиска

Содержание G700

Отзывы: