130
Options List
C.10
Option 12: OCXO and Four Additional Outputs
C.10.1
General Description
Option 12 for the Model 1088A/B adds a disciplined oven-controlled crystal oscillator (OCXO)
having stability of 1 part in 10
7
over temperature, and four additional configurable outputs.
C.10.2
Specifications
General
Output Connectors: BNC-type RF connectors (4).
Oscillator:
Oven-controlled, 1x10
−
7
, from 0 to 50
◦
C.
C.10.3
Firmware Setup for Option 12
Hardware and firmware configuration of the Model 1088A/B is performed at the factory when this
option is ordered at the same time as the clock. The following instructions are intended primarily
for field installation or maintenance. In addition, if the instrument configuration is ever reset to
factory default settings, then this initialization will need to be performed so that the units firmware
will automatically recognize the Option 12 assembly.
To change the firmware setup for Option 12, use the SETUP menu of the Model 1088A/B. Press
the SETUP key repeatedly until SET OPTION BOARD appears in the display. Press ENTER,
and then press the UP key until OPTION 12 appears. Press ENTER again, and select the option
(if any) present in the B option slot of the unit. Press ENTER again. This completes the firmware
configuration for Option 12. More information about instrument firmware configuration with the
SETUP menus is found in section 5 of the Model 1088A/B Operation Manual.
C.10.4
Main Board Setup via Internal Jumpers
Hardware and firmware configuration of the Model 1088A/B is performed at the factory when
this option is ordered at the same time as the clock. The instructions, which follow are intended
primarily for field installation.
Case Removal:
To change the main board configuration for Option 12, the top cover of the instrument must be
removed. Turn off the instrument, and disconnect the power cord. Using a T-25 torx driver, remove
the four screws holding the cover (and rack mount ears, if used) in place, and lift the cover off.
WARNING
Do not remove the top cover while power is applied. Hazardous voltages are present
while the power cord is connected. Always disconnect the unit from the input power source before
removal of the top cover.
Jumpers 2 and 3 of the main board assembly (see Figure 5.1) must be set properly to allow the
Option 12 oscillator to drive the clock. The setting for Jumper 2 should be changed to B (External
Reference) and the setting for Jumper 3 should be changed to B (5 MHz). When these settings
have been completed, reinstall the instrument cover and reapply power.
Содержание 1088A
