APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 219

Страница: 219 / 549

•

blocked signal in UP / blocked signal in DOWN / signal not plausible

Error cause:

•

If the signal is blocked in UP: internal spring of the switch blocked in UP

•

If the signal is blocked in DOWN: internal spring of the switch blocked in DOWN

•

If the signal is not plausible. this symptom is mainly caused by a gear shift (UP or DOWN)

detected by the control unit without any change to the signal status (from "released lever"

to UP or DOWN)

Troubleshooting:

This error necessarily involves an internal mechanical anomaly at the sensor; therefore, replace the

component.

NOTES: The potential presence of the P1900 electrical error disables the recognition of the P1906

error.

a-PRC setting buttons

Function:

To signal to the control unit the request for modi-

fication of the a-PRC system settings.

Operation / Operating principle:

Either control (+) or (-) is made up of a deviator

with both outputs electrically connected to the in-

strument panel: at the same time, the instrument

panel sends the requested command to the Marelli

ECU, via CAN line.

Electrical circuit diagram - Level in electrical

circuit diagram:

Traction control.

Position on vehicle:

On the left side semi-handlebar.

Position of connector (if applicable):

Inside the top fairing and instrument panel mount-

ing support.

Electrical specifications:

+ button: - 0 Ohm across PIN 2 and PIN 1 - Infinite

resistance across PIN 2 and PIN 5; - button: 0 Ohm

across PIN 3 and PIN 8 - infinite resistance across

PIN 3 and PIN 4.

Pin-out:

RSV4 1100 Factory

Electrical system

ELE SYS - 219

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды