APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 160

Страница: 160 / 549

Engine temperature sensor

Function

It is used to indicate to the control unit the engine

temperature, to optimise it behaviour and to cal-

culate the engine friction for a better estimation of

the to the delivered torque.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in electrical circuit diagram:

Temperature sensors

Position:

•

on the vehicle: on the right side, next to

the two big ends.

•

connector: on the sensor.

Electrical specifications:

•

Resistance at 25°: 2.05 k

± 100/

•

Resistance at 60°: 575

± 15 /

•

Resistance at 90°: 230

± 5 /

Pin out:

1. Greek/Black: Ground

2. Black

3. Yellow/Brown: 0-5 V signal

4. Black

DIAGNOSTIC TOOL: PARAMETERS

Engine temperature:

•

Example value with key ON: 25° C

•

Example value with engine on: 75° C

•

This is one of the values set by the ECU in the event of recovery mode: if there is a mal-

function after the engine start-up, the temperature is raised up to approximately 75°.

Engine temperature before Recovery:

•

Example value with key ON: -40° C

•

Example value with engine on: -40° C

•

Value determined from the signal read without taking into consideration the recovery mode:

the illustrative value refers to an open circuit.

Engine temperature at start-up:

Electrical system

RSV4 1100 Factory

ELE SYS - 160

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды