APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 212

Страница: 212 / 549

Troubleshooting:

•

Short-circuit to positive: disconnect the valve connector and check with the key ON if there

is ground continuity at PIN 5 of the connector: if there is voltage, disconnect the instrument

panel connector as well, and if there is voltage, restore the wiring harness and if there is no

voltage, replace the instrument panel; if there is no voltage, replace the motor.

•

If short circuit to negative, open circuit: check the valve connector and the instrument panel

connector: if they are not ok, restore; if they are ok, check continuity on the Brown/White: if

not ok, restore; if ok, with the two connector disconnected, check the ground insulation: if

there is ground continuity, disconnect the instrument panel connector as well, and if there

is ground, restore the wiring harness and if there is no ground, replace the instrument panel;

if there is no ground continuity, replace the motor.

DIAGNOSTIC TOOL: LOGIC ERRORS

P1500 Exhaust valve position

Functional diagnosis:

•

position error.

Error cause:

•

The position indicate by the potentiometer does not correspond to the one set by the control

unit.

This error is indicated by flashing the general warning light and by lighting up in a fixed manner the MI

warning light.

Troubleshooting:

•

Perform a mechanical check of the valve, check its normal rotation (with the cables discon-

nected from the motor, manually operate the cables and notice the movement regularity,

checking the complete stroke of the valve with the correct operation of the return spring) and

the absence of foreign objects that might obstruct its rotation: if not ok, restore; if ok, perform

the check procedure fro the valve connector and for the instrument panel connectors (ay

attention to oxidation signs) and check the cable resistance: if not ok, restore; if ok, with the

cables disconnected, check at key ON the normal rotation of the electric motor and replace

the motor (the potentiometer does not operate properly).

DIAGNOSTIC TOOL: ADJUSTABLE PARAMETERS

•

Exhaust valve zero search

NOTES: The motor is placed in a reference position to be able to perform subsequently the correct

mechanical stoppers search.

•

Exhaust valve self-learning

NOTES: Performs the minimum and maximum mechanical stoppers search.

CAUTION

Electrical system

RSV4 1100 Factory

ELE SYS - 212

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды