APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 218

Страница: 218 / 549

Engaged released.

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

P1900 Quick Shift sensor

Electrical diagnosis:

•

Short circuit to negative (at key ON) / Short circuit to positive (at key ON)

Error cause:

•

If short circuit to negative: voltage equal to zero is detected at PIN 11 at key ON.

•

If short circuit to positive: an excessive voltage is detected at PIN 11 at key ON.

This error is not indicated by lighting up any warning light.

Troubleshooting:

With disconnected sensor (voltage check):

•

Check if between PIN 1 and PIN 2 there is a 500 Ohm resistance by bringing the lever in

UP position; if NOT OK, replace the sensor;

•

Check if between PIN 1 and PIN 2 there is a 1000 Ohm resistance by bringing the lever in

DOWN position; if NOT OK, replace the sensor;

•

Check if between PIN 1 and PIN 2 there is a 1000 Ohm resistance with the lever released;

if NOT OK, replace the sensor;

•

Check if between PIN 2 and PIN 3 there is a 1000 Ohm resistance by bringing the lever in

UP position; if NOT OK, replace the sensor;

•

Check if between PIN 2 and PIN 3 there is a 500 Ohm resistance by bringing the lever in

DOWN position; if NOT OK, replace the sensor;

•

Check if between PIN 2 and PIN 3 there is a 1000 Ohm resistance with the lever released;

if NOT OK, replace the sensor;

With disconnected sensor (voltage check):

•

Check if between PIN 3 and PIN 2 there is a 3.3 V voltage by bringing the lever in UP position;

if NOT OK, replace the sensor;

•

Check if between PIN 3 and PIN 2 there is a 1.6 V voltage by bringing the lever in DOWN

position; if NOT OK, replace the sensor;

•

Check if between PIN 3 and PIN 2 there is a 2.5 V voltage with the lever released; if NOT

OK, replace the sensor;

If the above mentioned characteristics are fulfilled, it means that the sensor is functional and therefore

it will be necessary to check the wiring harness upstream the connector.

•

Red cable (PIN 2) in short circuit to ground.

•

Red cable (PIN 2) in short circuit to positive.

NOTES: The control unit can not detect faults due to missing cable continuity.

P1906 Quick Shift functional diagnosis

Electrical diagnosis:

Electrical system

RSV4 1100 Factory

ELE SYS - 218

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды