APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 460 | Manualshive

Страница: 460 / 549

background image

When sensors (3) detect a significant speed difference between the rear and the front wheels (for

example, when rearing up on the back wheel), the ABS system could take this as a dangerous situation.

In this case, 2 things may occur:

- the ABS system intervenes by releasing pressure from the calliper until the wheel turns again at the

same speed of the other wheel; it is not possible to brake for an instant.

- if the speed difference lasts long, the system may detect an error and deactivates the ABS system.

As a consequence, the system works as any regular braking system.

Riding with an active ABS system

•

During the vehicle start-up, after the in-

strument panel initial check, the ABS

warning light stops flashing when the

speed is under 5 km/h (3.1 mph).

If the ABS warning light remains on when the

vehicle is running, it means that a fault has

been detected and the ABS system has been

automatically deactivated.

IN CASE OF FAILURE OR WITH ABS DISCONNECTED,
THE VEHICLE OPERATES AS IF IT DID NOT HAVE THIS
SYSTEM.

NOTE

WHEN THE IGNITION KEY IS TURNED, IF THE SYSTEM IS FUNCTIONING CORRECTLY, THE
ABS INDICATOR LAMP WILL FLASH (THE SYSTEM IS ACTIVATED AS SOON AS THE VEHICLE
SPEED EXCEEDS 5 km/h - 3.1 mph)

Riding with the ABS system inactive

The warning light remains on in the stead state, the system has been deactivated.

Braking system

RSV4 1100 Factory

BRAK SYS - 460

«
...
458
459
460
461
462
...
»

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSV4 1100 Factory

HighLine ABF0166

Бренд: Mactronic Страницы: 2

Бренд: SmartTrike Страницы: 32

Indoor Cycle Computer

Бренд: Waters Fitness Страницы: 8

Бренд: Cardo Systems Страницы: 30

Бренд: Yerf-Dog Страницы: 7

Бренд: Magicshine Страницы: 12

Бренд: Steren Страницы: 2

Бренд: Sun Microsystems Страницы: 27

Бренд: Moustache Страницы: 98

Бренд: monkey lectric Страницы: 2

Бренд: 5th Wheel Страницы: 13

JETSTREAM P8 - 2009

Бренд: DAHON Страницы: 2

Бренд: SW Страницы: 14

Бренд: OFF CARR Страницы: 15

Бренд: SportRack Страницы: 8

Бренд: KBO Страницы: 22

Бренд: KBO Страницы: 26

Бренд: Milly Mally Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды