APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 211

Страница: 211 / 549

•

If open circuit: a too low current consumption was detected at PIN1/PIN10 of the instrument

panel connector.

•

If thermal protection: anomaly at the instrument panel.

•

If short circuit to negative: voltage equal to zero has been detected.

•

If short circuit to positive or short circuit between the two cables: excessive voltage has been

detected.

This error is indicated by flashing the general warning light and by lighting up in a fixed manner the MI

warning light.

Troubleshooting:

•

If open circuit: may be due to loose cables, in which case make sure that the cables are

stretched: if they are not, stretch them; if the cables are ok, perform the check procedure fro

the valve connector and for the instrument panel connector: if not ok restore; if ok, check

the continuity of the Brown/Green and Black/Red cables: if not ok, restore the wiring harness;

if ok, check the electrical characteristics of the engine and replace it, if necessary.

•

If thermal protection: replace the instrument panel.

•

If short circuit to negative: disconnect the valve connector and check with the key ON if there

is ground continuity at PIN 3 of the connector: if there is ground, disconnect the instrument

panel connector as well and if there is still ground, restore the Brown/Green cable and if

there is not, replace the instrument panel; if there is no ground, with key ON, check if there

is ground continuity at the connector PIN 2: if there is ground, disconnect the instrument

panel connector as well and if there is still ground, restore the Black/Red cable and if there

is not, replace the instrument panel; if there is no ground, check if PIN 3 or PIN 2 on the

motor have ground continuity: if they do, replace the motor.

•

If short circuit to positive or short circuit between the two cables: disconnect the instrument

panel connector and check with key ON if there is voltage on PIN 3 or PIN 2 of the connector:

if there is, restore the wiring harness; if there isn't, with key OFF and disconnecting the

exhaust connector as well, check if the two cables are insulated one from the other: if they

are not insulated, restore the wiring harness; if they are insulated, there is probably a short

circuit to positive that may be inside the motor or the instrument panel: it will be necessary

to try to replace one of the two components to identify which one of them is faulty.

P1503 Exhaust valve potentiometer

Electrical diagnosis:

•

short circuit to positive / short circuit to negative, open circuit.

Error cause:

•

Short-circuit to positive: excessive voltage has been detected on PIN 11 of the instrument

panel.

•

If short circuit to negative, open circuit: low voltage has been detected.

This error is indicated by lighting up in a fixed manner the MI warning light.

RSV4 1100 Factory

Electrical system

ELE SYS - 211

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды