APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 200

Страница: 200 / 549

•

Yes/No

gear engaged: 0 - 1 - 2- 3 - 4 - 5 - 6

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

P0914 Gear sensor

Electrical diagnosis:

•

short circuit to positive or open circuit / short circuit to negative / signal not plausible.

Error cause

•

If open circuit, short circuit to positive: excessive voltage has been detected on PIN 72.

•

If short circuit to negative: voltage equal to zero detected at PIN 72.

Troubleshooting

•

If open circuit, short circuit to positive: the error is detected only when the engine is on and

the vehicle is moving (gear engaged). check the sensor connector and the VEHICLE con-

nector of the control unit: if not ok, restore; if ok, check the continuity of the Grey/Black cable

between the two connectors: if not ok restore, if ok, with key ON (with the control unit con-

nector disconnected), check from the control unit connector side if the cable is energised: if

energised, disconnect the sensor connector and check if the cable is energised: if energised,

restore the wiring harness; if not energised, replace the sensor (there is an interruption or a

short circuit to positive of the Pink cable on the segment that goes from the sensor connector

to the sensor or inside the sensor).

•

If short circuit to negative: disconnect the sensor connector and, with key ON, check the

voltage of the Grey/Black cable: if it is zero, restore the wiring harness; if it approximately 5

V, replace the sensor (there is short circuit to ground of the Pink cable on the segment that

goes from the sensor connector to the sensor or inside the sensor).

CAUTION

IF THE ERROR IS SHOWN, IT MAY BE A FALSE CONTACT, SINCE IF THE PROBLEM PERSISTS,
IT SHOULDN'T BE POSSIBLE TO START TH VEHICLE.

Clutch lever sensor

Function

Indicates the clutch lever position to the control

unit.

Operation / Operating principle

If a gear is engaged but the clutch is engaged, that

is circuit closed to ground, there is consent to start

the vehicle.

Level in electrical circuit diagram:

Start enable switches

Electrical system

RSV4 1100 Factory

ELE SYS - 200

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды