APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 235

Страница: 235 / 549

Electrical diagnosis:

•

Intermittent signal or communication error

Error cause:

•

Probable bad contact in the CAN line.

This error is not indicated even in the ATT status.

Troubleshooting:

•

Perform the check procedure for the VEHICLE connector at PIN 66 and PIN 80 an of the

PIN B2 and PIN B3 of the engine-vehicle wiring harness connector; if it is NOT OK restore

and if it is OK perform the check procedure for PIN 2 and PIN 3 of inertial platform (Sensor

Box) connector; if NOT OK restore and if OK check the general operation of the Marelli

control unit and of the inertial platform (Sensor Box); in case of anomalies, replace the part

concerned.

NOTE

THIS ERROR DISABLES THE TRACTION CONTROL.

U1129 "LH handlebar" CAN line diagnosis

Electrical diagnosis:

•

no signal.

Error cause:

•

No signal is received from the LH light switch.

This error is indicated by lighting up in a fixed manner the general warning light.

Troubleshooting:

•

Check the connector of LH light switch: if not ok, restore; if ok, check the continuity of the

two lines from the LH light switch connector to the VEHICLE connector of the Marelli control

unit: if not ok, restore the wiring harness; if ok, replace the light switch.

NOTE

THIS ERROR DISABLES THE CRUISE CONTROL.

U1130 "LH handlebar" frame counter CAN line diagnosis

Electrical diagnosis:

•

Intermittent signal or communication error

Error cause:

•

Probable bad contact in the CAN line.

This error is not indicated even in the ATT status.

Troubleshooting:

•

Perform the check procedure for the VEHICLE connector at PIN 66 and PIN 80 an of the

PIN B2 and PIN B3 of the engine-vehicle wiring harness connector; if it is not OK restore

and if it is OK perform the check procedure for PIN 3 and PIN 4 of the LH light switch

RSV4 1100 Factory

Electrical system

ELE SYS - 235

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды