APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 549

background image

BEFORE STARTING ANY TROUBLESHOOTING PROCEDURES ON THE VEHICLE, CHECK THAT
THE BATTERY VOLTAGE IS ABOVE 12V.

CONNECTOR CHECK PROCEDURE

The procedure includes the following checks:

1. Observation and check of the connector correct

position on the component or on the coupling con-

nector, making sure that the locking catch is re-

leased.

2. Observation of the terminals on the connector:

no rust marks or dirt should be present and it is

important to check terminal correct positioning on

the connector (i.e., all terminals aligned at the

same depth) and terminal integrity (i.e., that termi-

nals are not loose, open/bent, etc.). For connec-

tors whose terminals are not visible (e.g. Marelli

control unit) use a metal cable of suitable diameter

and introduce it carefully in the connector slot at

the same depth as for the other terminals of the

connector.

CAUTION

IN THE CASE OF SPORADIC FAULTS, MOVE OR WIGGLE
THE RELATIVE WIRING HARNESS SLIGHTLY WHILE PER-
FORMING EACH OF THE CHECKS INDICATED FOR TROU-
BLESHOOTING.

3. Pull cables gently from the back of the connector to check that the terminals are fitted correctly on

the connector and that the wires are fastened correctly to the terminals.

Checking electrical CONTINUITY

Purpose of check:

the purpose of this check is ensure that there are no interruptions or excess re-

sistance (due to corroded terminals, for example) in the circuit under inspection.

Tester:

set the tester selector to the "continuity" symbol and place the probes of the tested at the two

ends of the circuit. Normally, the tester will sound an audible signal to confirm continuity in the section

of circuit tested. Continuity may also be tested by setting the tester selector to the "Ohm" symbol and

checking that the resistance in the circuit is zero or of a few tenths of an Ohm.

IMPORTANT: THE CIRCUIT MUST BE UNPOWERED DURING THIS TEST. IF THE CIRCUIT IS

POWERED, THE RESULTS OF THIS TEST ARE MEANINGLESS.

Checking GROUND CONNECTION

Purpose of check:

the purpose of this check is to verify that a cable or circuit is correctly connected

to the ground (-) of the vehicle.

Tester: set the tester selector to the "continuity" symbol and place one of the tester probes on the vehicle

ground point (or on the battery negative pole) and the other probe on the cable under inspection. Nor-

RSV4 1100 Factory

Electrical system

ELE SYS - 127

«
...
125
126
127
128
129
...
»

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSV4 1100 Factory

Бренд: Giant Страницы: 1

Бренд: DOCYKE Страницы: 41

Бренд: N-Com Страницы: 32

Бренд: Teasi Страницы: 15

infinity HD Series

Бренд: Evinci Страницы: 20

OIZ OMR CARBON 2019

Бренд: Orbea Страницы: 56

Бренд: Accolmile Страницы: 37

Бренд: Manitou Страницы: 43

Бренд: ewheels Страницы: 7

Timemachine TM01

Бренд: BMS Страницы: 172

Dirt Rocket MX350

Бренд: Razor Страницы: 45

Бренд: Marzocchi Страницы: 15

TENNECO 9001387

Бренд: Marzocchi Страницы: 88

Бренд: hepco & becker Страницы: 4

Бренд: Let's Go Aero Страницы: 3

Бренд: Boot Scoot Страницы: 2

RIDE 50 TRAIL/STREET

Бренд: FAZUA Страницы: 68

Бренд: Ozito Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды