APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 110

Страница: 110 / 549

WIRING TABLE I - EXHAUST VALVE MOTOR

ZONE

The fan wiring harness (1) must be fastened to the

ride by wire control wiring harness (2) by a clamp

(3).

Check that the grey safety lock (4) on the ride by

wire control connector, is locked in the lowered

position.

WIRING TABLE L - RIDE BY WIRE CONTROL

WIRING HARNESS

The ride by wire control wiring harness (1) must be

routed above the arm of the main wiring harness

(2) that branches towards the instrument cluster

and below the radiator hose (3), which connects

the thermostatic valve to the radiator.

CAUTION

IF THE RIDE BY WIRE CONTROL WIRING HARNESS IS
NOT ROUTED CORRECTLY IT MAY DAMAGE THE CON-
TROL.

WIRING TABLE L1 - RIDE BY WIRE CONTROL

WIRING HARNESS

The ride-by-wire control wiring (1) must be routed

externally with respect to the thermostatic valve

(2).

Electrical system

RSV4 1100 Factory

ELE SYS - 110

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды