APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 331

Страница: 331 / 549

•

Remove the two crankshaft and cam-

shaft reference pins.

•

Turn the crankshaft until the gear

screw covered by the head when the

hole on the camshaft gear is aligned

with the hole on the U bolt, is visible.

•

Block crankshaft rotation using one of

the specific tools.

•

Apply Loctite 243 thread lock on the

thread of the second gear fastener

screw. This screw must be replaced at

each reassembly.

•

Tighten the second camshaft gear fix-

ing screw to exactly the torque speci-

fied.

•

Remove the crankshaft locking tool.

Specific tooling

020850Y

Primary gear lock

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

020914Y

Flywheel stop

•

Turn the crankshaft back to the previous position in which the camshaft and U bolt holes

were aligned; Refit the reference pin while checking, using the crankshaft reference pin, that

the clutch side hole and the hole in the crankshaft are perfectly aligned.

•

If this is not the case, repeat the timing operations.

Specific tooling

020851Y

Camshaft timing pin

020852Y

Crankshaft timing pin

Rear head removal

•

Remove the rear head cover and the clutch cover.

•

Move cylinder piston 1 (left rear piston) to the TDC;

•

Turn the crankshaft 450° (one complete turn + 90°) in the direction of motor rotation (direction

of travel) in order to align the hole on the intake camshaft gear with the hole on the U-bolt.

This ensures that all the rear cylinder bank valve springs are decompressed.

RSV4 1100 Factory

Engine

ENG - 331

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды