APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 434 | Manualshive

Страница: 434 / 549

background image

CHECK AND, IF REQUIRED, REPLACE THE BEARINGS
AFTER EVERY BEARING REMOVAL.

Specific tooling

AP8140180

Bearing extractor

•

Remove the inner spacer (7) and collect the two OR seals (8).

•

Carefully clean inside the bearing seat.

CAUTION

WASH ALL COMPONENTS WITH CLEAN DETERGENT SOLUTION.

UPON REFITTING, USE A BUFFER WITH A DIAMETER EQUAL TO THE EXTERNAL RING OF THE
BEARINGS TO INSERT THE BEARINGS.
DO NOT HIT THE BALLS AND/OR THE INTERNAL RING.

CHECK THE CONDITION OF ALL COMPONENTS AND OF THE COMPONENTS INDICATED AS
FOLLOWS IN PARTICULAR.

SWINGARM BEARINGS

Carry out the check with the bearings fitted on the swingarm.

ROTATION CHECK

•

Manually rotate the inside ring of each bearing. Rotation must be constant, smooth and

noiseless.

If one or both bearings do not fall within the control parameters:

•

Replace both swingarm bearings.

RADIAL AND AXIAL CLEARANCE CHECK

•

Check the radial and axial clearance.

Axial clearance: a minimum axial clearance is allowed.

Radial clearance: none.

If one or both bearings do not fall within the control parameters:

•

Replace both swingarm bearings.

ALWAYS REPLACE BOTH BEARINGS.
ALWAYS REPLACE THE BEARINGS WITH COMPONENTS OF THE SAME TYPE.

SWINGARM SEALS

Chassis

RSV4 1100 Factory

CHAS - 434

«
...
432
433
434
435
436
...
»

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSV4 1100 Factory

Бренд: Felt Страницы: 22

Бренд: Felt Страницы: 29

Бренд: CICLOSPORT Страницы: 25

BIKBLM001YEL-UK

Бренд: Made Страницы: 183

Бренд: Fisher-Price Страницы: 16

Бренд: SRAM Страницы: 59

BIKVEL001GRE-UK

Бренд: Veloretti Страницы: 46

Бренд: Epic Cycles Страницы: 21

Бренд: Yedoo Страницы: 37

Бренд: ASOMTOM Страницы: 19

Бренд: Xtracycle Страницы: 6

Everyday BikePack

Бренд: Xtracycle Страницы: 8

Бренд: Xtracycle Страницы: 10

Бренд: e-bike vision Страницы: 9

Бренд: Bontrager Страницы: 18

Бренд: King-Meter Страницы: 6

Бренд: King-Meter Страницы: 10

Бренд: King-Meter Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды