APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 220

Страница: 220 / 549

•

PIN 1: + 12 V power supply (green-

brown)

•

PIN 2: ground (black-black)

•

PIN 3: ground (brown-black)

•

PIN 4: + 12 V power supply (blue-blue)

•

PIN 5: + 12 V power supply (yellow-

white)

•

PIN 8: power 12 V (red - pink)

DIAGNOSTIC TOOL: STATUSES

"+" button:

Pressed/Released/Invalid data due to open circuit error/Invalid data due to short circuit error.

"-" button:

Pressed/Released/Invalid data due to open circuit error/Invalid data due to short circuit error

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

P0569 "-" command plausibility

Electrical diagnosis:

•

Open contacts/Closed contacts

Error cause:

•

With open contacts, a voltage over zero is detected at the same time at PIN 22 and PIN 15

of the instrument panel.

•

With closed contacts, zero voltage is detected at the same time at PIN 22 and PIN 15 of the

instrument panel.

Troubleshooting:

The instrument panel expects to find, at either of the two PINs, a voltage over approx. 1 V and at the

same time a voltage below 1 V at the other PIN; if this does not occur, the instrument panel outputs the

information to the control unit that shows this error.

Indication on diagnostic tool "Invalid data due to short circuit error";

•

CASE 1): if this status is displayed with control not activated only, it means that a voltage

below 1V, instead of battery, is detected at PIN 22 of the instrument panel; disconnect the

"-" button connector and read voltage at PIN 22 of the instrument panel: if voltage is below

1 V, it means that on the red cable there is a short circuit to ground; if voltage is above 1 V

(approximately battery voltage), replace the "-" button sensor.

•

CASE 2): if this status is displayed only with control activated, it means that at that moment

a voltage below 1V, instead of battery, is being detected at PIN 15 of the instrument panel;

disconnect the gearshift control connector and read voltage at PIN 15 of the instrument

Electrical system

RSV4 1100 Factory

ELE SYS - 220

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды