APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 309

Страница: 309 / 549

Front head

Removing camshafts

•

Remove both head covers, the alter-

nator side cover and remove the cap

on the clutch cover in order to rotate

the crankshaft.

•

Remove the O ring.

•

Rotate the crankshaft via the opening on the clutch cover.

•

Position cylinder 1 piston (LH, rear piston) so that it is at the point where it crosses TDC.

•

rotate the crankshaft 150° in the engine rotation direction (direction of travel).

•

insert the respective pin, from the fly-

wheel side, into the groove on the

crankshaft.

NOTE

THE SPECIAL TOOL SHOWN HERE MUST ONLY BE USED
FOR IDENTIFYING THE CORRECT POSITION OF THE
CRANKSHAFT.
DO NOT USE IT FOR TIGHTENING COMPONENTS.

Specific tooling

020852Y

Crankshaft timing pin

•

Fit the pin for aligning the intake cam-

shaft with the hole on U-bolt.

•

If it was not possible before adjusting

the valve clearance, check the engine

timing.

Specific tooling

020851Y

Camshaft timing pin

RSV4 1100 Factory

Engine

ENG - 309

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды