APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 153

Страница: 153 / 549

3. A track signal (yellow cable)

4. B track power supply (orange/black cable)

5. Sensors 2 ground (pink/black cable)

6. B track signal (light blue cable)

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

P0225 Track A handle position sensor

Electrical diagnosis:

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

Short-circuit to positive: an excessive voltage was detected at PIN 39 of the ENGINE con-

nector.

•

If open circuit, short circuit to negative: a voltage equal to zero was detected at PIN 39 of

the ENGINE connector.

This error is indicated by flashing the general warning light and by lighting up in a fixed manner the MI

warning light.

Troubleshooting

•

Short-circuit to positive: check the value indicated by the parameter handle position sensor

track A: disconnect the connector and read the value indicated by the diagnostic tool: if the

voltage does not vary, there is a short circuit on the wiring harness of the relative cable, if

the voltage goes to zero, replace the handle sensor.

•

open circuit, short circuit to negative: check the handle sensor connector and engine control

unit connector, if not ok restore, if ok check cable continuity between the two terminals, if

not ok restore, if ok check the ground insulation of the cable (from the handle sensor con-

nector or control unit connector): if not ground insulated, restore the wiring harness, if ground

insulated check, with key ON, that power supply is present at PIN 1 of the potentiometer

and that the ground is present at PIN 2, if present correctly replace the handle sensor, if not

present check the continuity of the malfunctioning cable: if the continuity is present replace

the control unit, if not present replace the wiring harness

P2130 Track B handle position sensor

Electrical diagnosis:

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

Short-circuit to positive: an excessive voltage was detected at PIN 13 of the ENGINE con-

nector.

•

If open circuit, short circuit to negative: voltage equal to zero was detected at PIN 13 of the

ENGINE connector

RSV4 1100 Factory

Electrical system

ELE SYS - 153

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды