APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 223

Страница: 223 / 549

•

Pin 4: supply (brown)

DIAGNOSTIC TOOL: ELECTRICAL ERRORS

DIAGNOSTIC TOOL: LOGIC ERRORS

P1901 Ax acceleration sensor plausibility

Functional diagnosis:

•

Faulty sensor/Signal not valid

Troubleshooting:

With faulty sensor, the component inside the control unit is damaged and replacement of the control

unit is recommended. With signal not valid, the sensor has generated a signal out of range that is still

sent to the injection control unit together with the relevant error.

NOTE: The instrument panel does not indicate the presence of this error even in the ATT status.

NOTE

THIS ERROR DISABLES THE TRACTION CONTROL.

P1902 Az acceleration sensor plausibility

Functional diagnosis:

•

Faulty sensor/Signal not valid

Troubleshooting:

With faulty sensor, the component inside the control unit is damaged and replacement of the control

unit is recommended. With signal not valid, the sensor has generated a signal out of range that is still

sent to the injection control unit together with the relevant error.

NOTE: The instrument panel does not indicate the presence of this error even in the ATT status.

NOTE

THIS ERROR DISABLES THE TRACTION CONTROL.

P1903 Yaw sensor plausibility

Functional diagnosis:

•

Faulty sensor/Signal not valid

Troubleshooting:

With faulty sensor, the component inside the control unit is damaged and replacement of the control

unit is recommended. With signal not valid, the sensor has generated a signal out of range that is still

sent to the injection control unit together with the relevant error.

NOTE: The instrument panel does not indicate the presence of this error even in the ATT status.

NOTE

THIS ERROR DISABLES THE TRACTION CONTROL.

P1904 Roll sensor plausibility

Functional diagnosis:

•

Faulty sensor/Signal not valid

Troubleshooting:

RSV4 1100 Factory

Electrical system

ELE SYS - 223

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды