APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 85

Страница: 85 / 549

•

Apply Loctite 243 thread lock on the

thread of the timing gear fastener

screw. This screw must be replaced at

each reassembly.

•

Apply and loosely tighten the gear fix-

ing screw on the camshaft.

•

Block crankshaft rotation using one of

the specific tools.

•

Tighten the gear fixing screw on the

camshaft to exactly the torque speci-

fied.

•

Remove the crankshaft locking tool.

Specific tooling

020850Y

Primary gear lock

020914Y

Flywheel stop

•

Remove the two crankshaft and cam-

shaft reference pins.

•

Turn the crankshaft until the gear

screw covered by the head when the

hole on the camshaft gear is aligned

with the hole on the U bolt, is visible.

•

Block crankshaft rotation using one of

the specific tools.

•

Apply Loctite 243 thread lock on the

thread of the second gear fastener

screw. This screw must be replaced at

each reassembly.

•

Tighten the second camshaft gear fix-

ing screw to exactly the torque speci-

fied.

•

Remove the crankshaft locking tool.

•

Turn the crankshaft back to the previous position in which the camshaft and U bolt holes

were aligned; Refit the reference pin while checking, using the crankshaft reference pin, that

the clutch side hole and the hole in the crankshaft are perfectly aligned.

•

If this is not the case, repeat the timing operations.

RSV4 1100 Factory

Maintenance

MAIN - 85

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды