APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 325

Страница: 325 / 549

Removing camshafts

•

Remove the rear head cover and the clutch cover.

•

Move cylinder piston 1 (left rear piston) to the TDC;

•

Turn the crankshaft 450° (one complete turn + 90°) in the direction of motor rotation (direction

of travel).

•

Insert the pin from the clutch side into

the hole in the crankshaft.

NOTE

THE SPECIAL TOOL SHOWN HERE MUST ONLY BE USED
FOR IDENTIFYING THE CORRECT POSITION OF THE
CRANKSHAFT.
DO NOT USE IT FOR TIGHTENING COMPONENTS.

Specific tooling

020852Y

Crankshaft timing pin

•

Fit the pin for aligning the intake cam-

shaft with the hole on U-bolt.

•

If it was not possible before adjusting

the valve clearance, check the engine

timing.

Specific tooling

020851Y

Camshaft timing pin

•

Remove the two crankshaft and cam-

shaft reference pins.

•

Turn the crankshaft until the gear

screw covered by the head when the

hole on the camshaft gear is aligned

with the hole on the U bolt, is visible.

•

Block crankshaft rotation using one of

the specific tools.

•

Unscrew and remove the camshaft

gear screw.

•

Remove the crankshaft locking tool.

Specific tooling

020850Y

Primary gear lock

020914Y

Flywheel stop

RSV4 1100 Factory

Engine

ENG - 325

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды