APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 392

Страница: 392 / 549

Checking the throttle body

The throttle bodies are maintenance free and are

not serviceable. Replace the entire assembly in

the event of malfunction.

As all the internal components of the throttle body

assembly (potentiometers and electrical motor)

are contactless, no electrical diagnosis is possible.

Functional tests are performed on the throttle body

assembly by the control unit during vehicle oper-

ation, with the results visible on the diagnostic

instrument.

The only action possible before replacing the com-

ponent is checking the connectors and cable har-

nesses.

Installing the throttle body

•

When installing the throttle body, refer

to the electrical system section for the

correct cable routing.

•

Ensure that the injector connectors are

correctly fastened.

•

Connect the control unit connector, en-

suring that the security lock is in the

locked position.

Stepper motor

The control unit regulates the idle speed by controlling the throttle body motors directly. As a result, idle

speed adjustment and maintenance of the components involved in idle speed regulation (stepper mo-

tors, thermoactuators, etc.) are not necessary.

Power supply

RSV4 1100 Factory

P SUPP - 392

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды