3. Chain length on bicycles with rear suspension
The length of A will vary depending on the movement of the rear
suspension. Because of this, an excessive load may be placed
on the drive system if the chain length is too short. Set the
length of the chain by adding two links to the chain when the rear
suspension is at a position where dimension "A" is longest and
the chain is on the largest sprocket and the largest chainring. If
the amount of movement of the rear suspension is large, the
slack in the chain may not be taken up properly when the chain is
on the smallest chainring and smallest sprocket.
4. Outer casing length
(1) Loosen the B-tension adjustment screw until it is in the
position shown in the illustration.
(2) Check that there is enough slack in the outer casing. Next,
align the outer casing with the bottom edge of the outer
casing holder at the rear derailleur and
then cut of any excess length of outer
casing.
Connect the cable to the rear
derailleur and, after taking up
the initial slack in the cable,
re-secure to the rear
derailleur as shown in the
illustration.
Add 2 links (with the chain on both the largest
sprocket and the largest chainring)
Largest
sprocket
Chain
Largest
chainring
Series
RAPIDFIRE (Shifting lever)
Outer casing
Rear derailleur
Type
Freehub
Gears
Cassette sprocket
Chain
Bottom bracket guide
In order to realize the best performance, we recommend that the following combination be used.
Specifications
Model number
Type
Gears
Total capacity
Applicable sprocket combination
Smallest sprocket
Front chainwheel tooth difference
Rear Derailleur
Installation of the rear derailleur
5 mm Allen key
Dropout
Bracket
Bracket spindle
Tightening torque :
8 - 10 N·m {70 - 86 in. lbs.}
General Safety Information
WARNING
“Maintenance interval depends on the usage and riding circumstances.
Clean regularly the chain with an appropriate chaincleaner. Never use
alkali based or acid based solvents such as rust cleaners. If those solvent
be used chain might break and cause serious injury.”
•
If it is difficult to install the wheel, install the quick release lever on the rotor
side. If doing this, make sure that the quick release lever does not interfere with
the rotor and that burns do not occur.
•
In order to obtain good gear shifting performance, this chain has a forward side
and a reverse side, and the sides are marked so that the chain will face the
correct way when installed. The proper design performance will be obtained when
the chain is installed so that it faces the correct way. If it is installed so that it
faces the opposite way, the chain may come off and the bicycle may fall over and
serious injury may occur as a result.
• Use the reinforced connecting pin only for connecting the narrow type of chain.
• If connecting pins other than reinforced connecting pins are used, or if a reinforced connecting
pin or tool which is not
suitable for the type of
chain is used, sufficient
connection force may not
be obtained, which could
cause the chain to break
or fall off.
• Make sure that the
connecting pin is aligned with the outer link surface from the side that
the pin is inserted. It should feel smooth and flush when you run your
finger over it. The pin will protrude slightly on the backside after the
break off pin is removed.
• If it is necessary to adjust the length of the chain due to a change in the
number of sprocket teeth, make the cut at some other place than the
place where the chain has been joined using a reinforced connecting
pin. The chain will be damaged if it is cut at a place where it has been
joined with a reinforced connecting pin.
• Check that the tension of the chain is correct and that the chain
is not damaged. If the tension is too weak or the chain is
damaged, the chain should be replaced. If this is not done, the
chain may break and cause serious injury.
•
Obtain and read the service instructions carefully prior to
installing the parts.
Loose, worn or damaged parts may cause the bicycle to fall over and serious
injury may occur as a result. We strongly recommend only using genuine Shimano replacement
parts.
•
Obtain and read the service instructions carefully prior to installing the parts.
If adjustments
are not carried out correctly, the chain may come off and this may cause you to fall off the bicycle
which could result in serious injury.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later
reference.
Note
• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.
• If the amount of looseness in the links is so great that adjustment is not possible, you should
replace the derailleur.
• You should periodically clean the derailleur and lubricate all moving parts (mechanism and
pulleys).
• If gear shifting adjustment cannot be carried out, check the degree of parallelism at the rear end
of the bicycle. Also check if the cable is lubricated and if the outer casing is too long or too short.
• If you hear abnormal noise as a result of looseness in a pulley, you should replace the pulley.
• If the chain keeps coming off the sprockets during use, replace the sprockets and the chain.
• Use a frame with internal cable routing is strongly discouraged as it has tendencies to impair the
SIS shifting function due to its high cable resistance.
• Always be sure to use the sprocket set bearing the same group marks.
Never use in combination with a sprocket bearing a different group mark.
• Use an outer casing which still has some length to spare even when the
handlebars are turned all the way to both sides. Furthermore, check that the
shifting lever does not touch the bicycle frame when the handlebars are
turned all the way.
• A special grease is used for the gear shifting cable. Do not use DURA-ACE
grease or other types of grease, otherwise they may cause deterioration in
gear shifting performance.
• Grease the inner cable and the inside of the outer casing before use to ensure that they slide
properly.
• For smooth operation, use the specified outer casing and the bottom bracket cable guide.
• Operation of the levers related to gear shifting should be made only when the front chainwheel is
turning.
• The tension pulley has an arrow on it to indicate the direction of rotation. Install the tension pulley
so that the arrow is pointing clockwise when looking at the outer side of the derailleur.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For maximum performance we highly recommend Shimano lubricants and maintenance products
• For any questions regarding methods of installation, adjustment, maintenance or operation,
please contact a professional bicycle dealer.
g
a -18T
-
S
H
IM
AN
O
HYP
ERG
LID
E
C
ag-15T
ag-1
3T
Group marks
1. Top adjustment
Turn the top adjustment screw to adjust so that the guide pulley is in line with the outer line of
the smallest sprocket when looking from the rear.
2. Low adjustment
Turn the low adjustment screw so that the guide pulley moves to a position directly in line with
the largest sprocket.
SIS Adjustment
Top adjustment
screw
Guide pulley
Pull
Less than 30 mm
Tightening torque :
6 - 7 N·m {52 - 60 in. lbs.}
Groove
Note:
Be sure that the cable is
securely in the groove.
Low adjustment
screw
Cutting the outer casing
When cutting the outer casing, cut the opposite end to the end
with the marking. After cutting the outer
casing, make the end round so that the
inside of the hole has a uniform diameter.
Attach the same outer
end cap to the cut end
of the outer casing.
Outer end cap
* If the rear derailleur moves to a large degree, such as in
bicycles with rear suspension, it is recommended that you
replace the cap with the
accessory aluminum cap.
The end of the outer casing
which has the aluminum cap
should be at the derailleur side.
Aluminum cap
Derailleur side
The sealed cap with
tongue and the rubber
shield should be
installed to the outer
casing stopper of the
frame.
Rubber shield
Rubber shield
Be careful not to bend
Sealed cap with tongue
5. How to use the B-tension adjustment screw
Mount the chain on the smallest chainring and the largest
sprocket, and turn the crank arm to shift gears. Then turn the B-
tension adjustment screw
to adjust so that the guide
pulley does not interfere
with the sprocket but not so
close that it touches the
chain. Next, set the chain
to the smallest sprocket
and repeat the above to
make sure that the pulley
does not touch the
sprocket.
■
Replacing the rear derailleur
<Checking the distance between the largest sprocket
and the guide pulley>
Set the rear derailleur to the lowest gear
position, stop the wheel from turning, and then
check that the distance from the edge of the
guide pulley to the edge of the largest sprocket
is within the range of 5 - 6 mm. Turn the crank
arm to shift gears and check that there is no
roughness in the feel. If the number of teeth for the cassette
sprocket is changed, carry out this setting again.
Largest sprocket
Smallest sprocket
B-tension
adjustment screw
6. SIS Adjustment
Operate the shifting lever several times to move the chain to the
2nd sprocket. Then, while pressing the lever just enough to take
up the play in the lever, turn the crank arm.
When shifting to
3rd
Tighten the outer casing
adjustment barrel until the
chain returns to the 2nd
sprocket. (clockwise)
Loosen the outer casing
adjustment barrel until the
chain touches the 3rd sprocket
and makes noise. (counter
clockwise)
When no sound
at all is heard
Best setting
The best setting is when the shifting lever is
operated just enough to take up the play and the
chain touches the 3rd sprocket and makes noise.
* Return the lever to its original position (the position where
the lever is at the 2nd sprocket setting and it has been
released) and then turn the crank arm clockwise. If the
chain is touching the 3rd sprocket and making noise, turn the outer
casing adjustment barrel clockwise slightly to tighten it until the noise
stops and the chain runs smoothly.
Operate lever to change gears, and check that no noise occurs
in any of the gear positions.
For the best SIS performance, periodically lubricate all
power-transmission parts.
Adjustment bolt
Adjustment bolt
Note:
The distance between the outer stopper to the outer casing
holder of the rear derailleur may change when the rear
suspension moves, so determine the length of the outer casing at
the point where this length is at its greatest.
Note:
Set the inner cable so that it protrudes by a
length of less than about 30 mm, and then
check that the inner cable does not interfere with
the spokes of the wheel. Stop the wheel from
turning while carrying out this step.
* Service Instructions in further languages are available at :
http://techdocs.shimano.com
Please note: specifications are subject to change for improvement without notice. (English)
© Jan. 2010 by Shimano Inc. XBC SZK Printed in Japan.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
This service instruction explains how to use and maintain the
Shimano bicycle parts which have been used on your new bicycle.
For any questions regarding your bicycle or other matters which
are not related to Shimano parts, please contact the place of
purchase or the bicycle manufacturer.
Outer casing
Guide pulley
Largest sprocket
Outer line of
smallest sprocket
(1)
(2)
Guide pulley / Tension pulley
Tightening torque :
2.5 - 5.0 N·m {22 - 44 in. lbs.}
SI-5XF0A-001-00
Technical Service Instructions
SI-5XF0A-001
RD-M773 / RD-M663
Rear derailleur
Reinforced Connecting Pin
Link Pin
Link Pin
Link surface
Connecting pin
Chain tool
Chain
10-speed super narrow
chain for MTB
Reinforced
connecting pin
TL-CN32
TL-CN23
TL-CN27
with groove (3)
with groove (2)
3 mm Allen key
SLX
SL-M660-10R
OT-SP41 (SIS-SP41)
RD-M663
SGS
FH-M665
10
CS-HG81-10
CN-HG74
SM-SP17
XT
SL-M770-10R
OT-SP41 (SIS-SP41)
RD-M773
SGS / GS
FH-M770 / M775
10
CS-M771-10
CN-HG94
SM-SP17 / BT17
Note:
Periodically check that there is no gap between the dropout
and the bracket as shown in the illustration. If there is a gap between
these two parts, problems with gear shifting performance may occur.
RD-M663
SGS
10
43T
11 - 32T, 11 - 34T, 11 - 36T
11T
18T
RD-M773
SGS
GS
10
43T
11 - 32T, 11 - 34T, 11 - 36T
11T
18T
10
35T
11T
18T
Outer casing holder
