APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 150

Страница: 150 / 549

C1031 Rear wheel speed sensor

Electrical diagnosis:

Open circuit, short circuit to negative or short circuit to positive.

Error cause:

•

Open circuit: circuit interruption detected.

•

Short-circuit to negative: null voltage detected on PIN 14 of the ABS control unit.

•

Short-circuit to positive: excessive voltage detected on PIN 14 of the ABS control unit.

Troubleshooting:

Open circuit:

- Check the connectors on the component and on the ABS control unit.

- Check the integrity and continuity of the wiring harnesses:

•

between PIN 14 of the ABS control unit and PIN 1 of the sensor (yellow cable)

•

between PIN 13 of the ABS control unit and PIN 2 of the sensor (yellow/brown cable)

Short-circuit to negative:

- Disconnect the sensor connector.

- Check the ground insulation of the two PINs.

- If there is no insulation, restore the wiring harness or replace the sensor.

Short-circuit to positive:

- Disconnect the sensor connector.

- Check the battery supply insulation of the two PINS.

- If there is no insulation, restore the wiring harness or replace the sensor.

P2158 Rear wheel speed sensor/signal

•

Connect to the ABS control unit diagnosis.

DIAGNOSTIC TOOL: LOGIC ERRORS

C1032 Rear wheel speed sensor

Functional diagnosis:

Signal not plausible.

Error cause:

•

Possible tone wheel fault due to deformations or dirt.

Troubleshooting:

- Check that the tone wheel is not damaged and is clean.

- Check that the number of teeth on the tone wheel is correct.

- Check that the tone wheel and the sensor are correctly positioned;

- Check that the tyre is the correct size.

- If all these checks are positive, replace the sensor.

P2162 Wheel speed plausibility

Error cause:

Electrical system

RSV4 1100 Factory

ELE SYS - 150

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды