APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 237

Страница: 237 / 549

and PIN 2 of the ABS control unit: if NOT OK, replace the vehicle wiring harness, if OK,

check the continuity between PIN 2 of the inertial platform (Sensor box) and PIN 11 of the

ABS control unit; if NOT OK, replace the wiring harness, if OK, check the correct power

supply to PIN 4 (12V) and the grounding of ABS control unit PIN 1: if NOT OK, restore the

wiring harness, if OK, replace the inertial platform (sensor box)

•

Configuration error - Open the diagnostic tool devices status page to check if the control unit

setting is actually consistent with the motorcycle setting. Example: if the vehicle is equipped

with inertia sensor platform (Sensor box), the correct status we should find on the diagnostic

tool devices status page will be: Aprilia Traction Control Performance (in a bend) PRESENT.

While on a vehicle equipped with inertia sensor platform (Sensor box) and diagnostic tool

indication: Aprilia Traction Control Performance (in a bend) NOT PRESENT update the

control unit

NOTE

THIS ERROR DISABLES THE TRACTION CONTROL.

U1121 Diagnosis of "ABS control unit" CAN line or CLF frame counter

Functional diagnosis:

•

Signal absent

Error cause:

•

If there is no signal, no signal is received from the ABS control unit.

This error is indicated by lighting up in a fixed manner the MI warning light.

Troubleshooting:

•

Missing signal - Perform the check procedure for pin 2 and 11 of the ABS control unit con-

nector, for pin 66 and 80 of the Marelli control unit vehicle connector: if NOT OK, restore; if

OK with key OFF, disconnect the ABS control unit connector; if NOT OK replace the wiring

harness, if OK check the correct power supply to PIN 18 (12V) and the grounding of ABS

control unit PIN 1; if NOT OK, restore the wiring harness, if OK, replace the ABS control unit.

NOTE

THE PRESENCE OF THIS ERROR DETERMINE THE DEACTIVATION OF THE TRACTION CON-
TROL AND THE CRUISE CONTROL.

P1800 Rear wheel radius learning diagnosis

Functional diagnosis:

•

CAN error while learning / Signal not plausible.

Error cause:

•

In case of CAN error during acquisition, system warns that the procedure can not be com-

pleted due to a communication problem on the CAN line.

RSV4 1100 Factory

Electrical system

ELE SYS - 237

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды