APRILIA RSV4 1100 Factory Скачать руководство пользователя страница 543

Страница: 543 / 549

- Do not carry the battery together with flammable, explosive or sharp objects.

- NEVER attempt to open the battery.

- Keep the connecting poles clean and firmly secured at all times.

- Do not immerse the battery in water, or leave it exposed to moisture.

- Do not connect the battery directly to wall outlets.

- Do not subject the battery to short circuit by connecting cables or other metallic objects to the positive

and negative terminals.

- Do not pierce the battery casing with nails or other sharp objects, do not try to forcibly open it or step

on it.

- Do not perform welds on the battery terminals.

- Do not use the battery in combination with primary batteries (such as dry batteries) or batteries of

different capacity, type and brand.

- Do not use the battery if it emits a strange odour, emits heat, changes colour or deforms, or if it presents

any anomaly. Stop use immediately if the battery is in use or under charge.

THE BATTERY DOES NOT CONTAIN HARMFUL POLLUTANTS, CORROSIVE ACIDS OR TOXIC

HEAVY METALS

Levels check

- Hydraulic braking system fluid level

- Clutch system fluid level

- Engine coolant level

- Engine oil level

Road test

- Cold start

- Instrument panel operation

- Response to throttle control

- Stability when accelerating and braking

- Front and rear brake efficiency

- Front and rear suspension efficiency

- Abnormal noise

Static test

Static control after the test drive:

- Restarting when warmed up

- Idling

- Uniform turning of the steering

RSV4 1100 Factory

Pre-delivery

PRE DE - 543

Содержание RSV4 1100 Factory






































































































































































































































































































































































































































































































































































Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды

APRILIA RSV4 1100 Factory, Руководство по обслуживанию станции

Результаты поиска

Содержание RSV4 1100 Factory

Отзывы:

Похожие инструкции для RSV4 1100 Factory

Бренды по названию

Популярные бренды