background image

PathFinder II Wireless (#500-108)

& PathFinder II (#500-109) 

Patent NO.: 7.988.344

Warning: Inseting the mini-CD into a slot-loading

drive may damage your drive.

1

2

3

Step 1:

 Press the notch at the 

             bottom of the computer

             to detach the cover on

             the computer. 

 Step 1:

 Attach the wireless speed sensor & rubber 

              pad to the front of the left fork or the back

              of the right fork leg using screw strap or 

              zip-ties provided.

 Step 2:

 Adjust the sensor and magnet spacing with

              the spacer. Remove the spacer after fixing

              the sensor in its final position.  

             

 Step 3:

 Press the 

Alignment Button

 to check if

              the speed sensor has been aligned correctly

              with the magnet. If successfully aligned, 

              the speed sensor will produce a beeping

              sound when the magnet moves over the

              speed sensor.   

             

Attach the wired speed sensor with the

              zip-ties supplied and tighten the bladed

              spoke magnet to the bicycle.
 

             

Step 2:

 Align the notches on the

             light with the holes on the

             computer. Press and lock 

             the light housing to the 

             computer.

Step 3:

 The light and the computer

             are now ready to use.

The head unit of PathFinder II series computer

uses a CR2032, 3-Volt Lithium button cell battery

while the headlight is powered by 3xAAA batteries. 

For PathFinder II Wireless: 

The wireless speed sensor uses an A23, 12-Volt

battery.

For PathFinder II: 

Installing Speed Sensor & Magnet

Installation

Installing the Headlight

Installing the Battery

Installing the Mounting Bracket & Head Unit

For PathFinder II Wireless: 

For PathFinder II Wireless:

For PathFinder II:

Note:

 Mount the sensor as high up

          on the fork leg as possible.

 Step 2:

 Adjust the sensor and magnet spacing 

              with the spacer.  

Step 3:

 Remove the spacer after tightening the

zip-tie down to hold the sensor in its final position.

         To avoid damaging or cutting the wires 

accidentally, use the tape provided with the 

package (NOT the zip-ties) to secure wires to

 the frame, fork, bars or stem.  

Make sure excess wire is taped down or wrapped

around brake cable housing. Be sure to leave 

enough slack in the wire to accommodate the 

movement of fork and handbar.

Button     :  Freeze Frame Memories

Button     :  Mode-Advance to next mode

Button     :  Enter Setup Mode

Button     :  Headlight Mode-Scroll different modes 

of the headlight (ON    FLASH    OFF)

Button    &    :  Reset Ride Date Including Frozen 

                       Screens

Button    :  Recall Freeze Frame Memories

Button    ,     &    :  Total Clear Reset

In Normal Operation

In Initial Setup

Button      is used to toggle between different  

settings and to confirm the selected value.

Button     is used to scroll through the values 

(0~9) (press & hold for fast advance).

 Button Function and Setup 

PathFinder II series cycling computer is programmed

to enter the Intial Setup Mode after replacement

of new battery or All Clear Total Reset.  

1

2

3

4

Press Momentarily:

Press & Hold for 2 Seconds:

1

1

1

1

1

2

2

2

2

3

4

4

3

1

2

2

4

12 / 24 Clock

Front

Front

Front

Front

Using Zip-Ties:

Using Screw Strap:

OR

Using Zip-Ties:

OR

Using Screw Strap: Using Zip-Ties:

Detaching the Computer

Press

Wire Securing Tape

QUICK START MANUAL

 Step 1: 

For more details, please refer to the full manual 

inside the mini-CD included with the product.

Отзывы: