APRILIA CAPONORD 1200 Скачать руководство пользователя страница 258

Страница: 258 / 439

•

Remove the valves.

Valve check

CAUTION

REPLACE THE VALVES ONE AT A TIME. DO NOT MIX THE COMPONENTS. EACH VALVE MUST
BE INSERTED INTO ITS SEAT, WHICH IS MARKED PRIOR TO REMOVAL.

VALVE STEM DEVIATION

Lift up the valve approx. 10 mm (0.39 in) from its

seat.

Measure the valve stem deviation in two perpen-

dicular directions and position the dial gauge as

shown in the figure.

If the measured deviation exceeds the specified

limit, determine if the valve or the guide must be

replaced.

Characteristic

Valve stem distortion

0.25 mm (0.0098 in)

If the valve stem, when measured with a micro-

meter, is worn to its limit and the clearance ex-

ceeds the specified limit, replace the valve.

If the valve stem lies within the specific limit, re-

place the valve guide.

Recheck the clearance after replacing the valve or

the guide.

Characteristic

Intake valve stem diameter

5.987 - 5.973 mm (0.2357 - 0.2352 in)

Exhaust valve stem diameter

5.975 - 5.960 mm (0.2352 - 0.2346 in)

Engine

CAPONORD 1200

ENG - 258

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды