APRILIA CAPONORD 1200 Скачать руководство пользователя страница 121

Страница: 121 / 439

that is not functioning properly: if there is continuity, replace the control unit; if not, restore

the wiring

DIAGNOSTICS INSTRUMENT: LOGIC ERRORS

Blue front connector throttle grip position (tracks A-B) P0154

•

inconsistent signal

Error cause

•

Two illogical voltage signals have been detected at PIN 13 and 39 of the ENGINE connector

(tracks A-B)

Troubleshooting

•

Check the parameters of the blue front connector Throttle Grip Position Sensor - tracks A

and B: if one of the two values clearly deviates from 600-1400 mV, it means that this po-

tentiometer is defective. Check the throttle grip sensor connector and the control unit

connector: if not OK, restore. If OK, check that cable resistance between the throttle grip

sensor connector and the control unit is a few tenths of Ohm: if this is not the case, restore

wiring. If the value is correct, replace the complete throttle grip sensor

White rear connector throttle grip position (tracks C-D) P0155

•

inconsistent signal

Error cause

•

Two illogical voltage signals have been detected at PIN 23 and 11 of the ENGINE connector

(tracks A-B)

Troubleshooting

•

Check the parameters of the white rear connector Throttle Grip Position Sensor - tracks C

and D: if one of the two values clearly deviates from 600-1400 mV, it means that this po-

tentiometer is defective. Check the throttle grip sensor connector and the control unit

connector: if not OK, restore. If OK, check that cable resistance between the throttle grip

sensor connector and the control unit is a few tenths of Ohm: if this is not the case, restore

wiring. If the value is correct, replace the complete throttle grip sensor

Throttle grip position P0156

•

inconsistent signal

Error cause

•

The value of the front side sensor (tracks A-B) does not coincide with the value of the rear

sensor (tracks C-D)

Troubleshooting

•

Replace the throttle grip sensor

DIAGNOSTICS INSTRUMENT: ADJUSTABLE PARAMETERS

Handle self-learning: -

CAPONORD 1200

Electrical system

ELE SYS - 121

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды