APRILIA CAPONORD 1200 Скачать руководство пользователя страница 166

Страница: 166 / 439

•

excessive time / search not performed, wrong stroke

Error cause

•

If time is excessive: failed memorisation of the travel limit positions of the valve. The EVC

control unit is not able to record the valve's travel limits: possible interruption of the circuit.

If research has not been carried out or wrong stroke: failed memorisation of the travel limit

positions of the valve: this occurs in case of first ignition of the motorbike or following a reset

of the control unit.

Troubleshooting

•

If time is excessive: check the connector on the component and the EVC connector. Dis-

connect the two connectors and check the continuity of the cable between the PIN 4 engine

- PIN C1 EVC and between PIN 5 engine - PIN A1 EVC. If all the above-mentioned tests

have a positive outcome, replace the motor.

•

If research has not been carried out or wrong stroke: carry out the self-learning procedure

using the diagnosis instrument.

Exhaust valve engine P0192

•

open circuit / shortcircuit to negative / shortcircuit to positive, shortcircuit between the two

cables

Error cause

•

If the circuit is open: an interruption of the circuit has been detected. If shorted to negative:

a null tension has been detected on PIN A1 or on PIN C1 EVC. If shorted to positive or short

circuit between both cables: an excessive tension has been detected on PIN A1 or on PIN

C1 EVC.

Troubleshooting

•

If the circuit is open: check the connector on the component and the EVC connector. Dis-

connect the two connectors and check the continuity of the cable between the PIN 4 engine

- PIN C1 EVC and between PIN 5 engine - PIN A1 EVC. If the cable harness is not damaged,

replace the component.

•

If shorted to negative: disconnect the connector of the engine and check its insulation from

ground of PIN 4 and 5: if the insulation is not present, restore the cabling, otherwise replace

the component.

•

If shorted to positive or short circuit between both cables: check the connector on the com-

ponent and the EVC connector. Disconnect the connector of the component and check its

insulation from supply system of PIN 4 and 5; also ensure that the two PINs are insulated

between each other. If all the above-mentioned tests have a positive outcome, replace the

component.

Exhaust valve potentiometer P0193

Electrical system

CAPONORD 1200

ELE SYS - 166

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды