APRILIA CAPONORD 1200 Скачать руководство пользователя

Страница: 90 / 439

Check the mapping of the control unit and reset the vehicle configuration.

OIL SENSOR

Error code B0001 (OIL SENSOR FAILURE)

Oil motor low pressure alarm:

This alarm occurs when the engine is off and the pressure of the engine oil is low. If during the following

OFF-ON key switching, the fault is not immediately detected, the error is no longer displayed. Only in

case the fault occurs again after performing two TRIPs (minimum TRIP: 10 km) and following the third

OFF-ON key switching, the error is displayed again.

Identification

Oil warning light fixed.

Troubleshooting

Check the connector on the component and the instrument panel connector. Disconnect the two con-

nectors and check the continuity of the cable between the sensor and the PIN 17 of the instrument panel

(grey connector) and restore the cable harness. If the cable harness is not damaged, replace the sensor.

Error code B0002 (OIL PRESSURE FAILURE)

Oil sensor disconnected alarm:

This alarm occurs when the sensor is disconnected, rpm higher than 900.

Identification

Oil warning light flashing.

Troubleshooting

Disconnect the connector of the component and check the insulation from ground: if the insulation is

not present, restore the cabling, otherwise replace the sensor. It this error persists, use a pressure

gauge to check the pressure of the oil in the engine circuit.

CAN LINE

Error code B0008 (CAN LINE RECEPTION ERROR)

Error cause

The instrument panel is coded at the first key insertion, if the CAN line is missing, the error is activated.

Identification

Warning light on.

Troubleshooting

Check the cable harness of the CAN line.

Error code B0009 (CAN LINE TRANSMISSION ERROR)

Error cause

The instrument panel is coded at the first insertion of the key, if the received data do not coincide with

the memorised ones, the error is activated.

Identification

Warning light on.

Troubleshooting

Electrical system

CAPONORD 1200

ELE SYS - 90

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды