APRILIA CAPONORD 1200 Скачать руководство пользователя страница 164

Страница: 164 / 439

of the valve; the logic and the control of the motor

are provided by the VCU control unit (Caponord

1200 Travel Pack) or by the EVC control unit (Ca-

ponord 1200).

The motor is fitted with an integrated potentiome-

ter for controlling the position. The exhaust butter-

fly valve is managed as follows:

•

With engine off: open by 75%;

•

With engine running: regardless of the

gear, at low revolutions and small throt-

tle opening, it is completely closed; if

the revolutions or the throttle opening

exceed preset thresholds defined dur-

ing calibration, it is completely open,

otherwise it is in an intermediate posi-

tion. With bike stopped and in neutral

the valve stays closed, regardless of

rpm.

Level in electrical circuit diagram:

Exhaust valve control unit - Caponord 1200

VCU (Vehicle Control Unit) control unit - Caponord

1200 Travel Pack

Location:

•

On the vehicle: The motor is placed in

the front lower part of the engine.

•

The valve in the exhaust duct.

•

Connector: on the motor.

Connector:

1. Caponord 1200

2. Caponord 1200 Travel Pack

Pin out:

1. Supply from VCU

2. Exhaust valve potentiometer signal

3. Ground from VCU

4. Exhaust valve positive

5. Exhaust valve negative

Electrical system

CAPONORD 1200

ELE SYS - 164

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды