manualshive.com logo in svg

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Априлия Капонорд 1200 - это мощный мотоцикл для дальних поездок. Если вам нужен Service Station Manual или инструкция по эксплуатации, вы можете скачать его бесплатно с manualshive.com. Получите все необходимые сведения для обслуживания вашего мотоцикла в одном месте.

Поделиться
Скачать
background image

1. Ground connection

2. Voltage 12V

Electrical specifications:

•

Side Stand Up: closed circuit (continu-

ity)

•

Side Stand Down: open circuit (infinite

resistance)

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: STATUSES

Side stand sensor: up/down

•

indication on the diagnostics instrument always down: check the connector: if not OK, re-

store; if it is OK, disconnect the two terminals from the sensor and check continuity to ground

of PIN 1: if there is no continuity, restore the cable harness; if there is, replace the sensor.

•

Indication on the diagnostics instrument always up: disconnect the terminals from the sensor

and check if there is continuity between the two PINS, with stand down: if there is continuity,

replace the sensor; if the circuit is open, it means that the brown/green cable from sensor

PIN 2 to VEHICLE connector PIN 70 is short circuit to ground: restore the cable harness.

Bank angle sensor

(IF APPLICABLE)

Function

It tells the vehicle position to the control unit.

Operation / Operating principle

When the sensor is inverted, the circuit is closed

to ground: When the Marelli control unit detects

this ground connection, it does not enable start-up

or shuts off the engine.

Level in electrical circuit diagram:

Start-up enabling switches

Location:

•

on the vehicle: under the saddle, be-

hind the battery.

•

connector: next to the sensor (4-ways

connector).

CAPONORD 1200

Electrical system

ELE SYS - 159

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CAPONORD 1200

KYMCO Dink 50 Service Manual preview
Dink 50
Бренд: KYMCO Страницы: 424
SUR-RON Light Bee Service Manual preview
Light Bee
Бренд: SUR-RON Страницы: 50
Suzuki 1987 GSX-R150 Service Manual preview
1987 GSX-R150
Бренд: Suzuki Страницы: 311
R&G CP0466 Series Fitting Instructions Manual preview
CP0466 Series
Бренд: R&G Страницы: 9
RDMOTO CF124 Quick Start Manual preview
CF124
Бренд: RDMOTO Страницы: 2
paladin P4009 Installation And Owner'S Manual preview
P4009
Бренд: paladin Страницы: 2
Yamaha YZ125 2016 Owner'S Service Manual preview
YZ125 2016
Бренд: Yamaha Страницы: 166
Yamaha YZ125 2015 Owner'S Service Manual preview
YZ125 2015
Бренд: Yamaha Страницы: 166
Yamaha YZ250F(D) Owner'S Service Manual preview
YZ250F(D)
Бренд: Yamaha Страницы: 198
Yamaha YZ250 2022 Owner'S Service Manual preview
YZ250 2022
Бренд: Yamaha Страницы: 274
Yamaha YZ250F(E) Owner'S Service Manual preview
YZ250F(E)
Бренд: Yamaha Страницы: 356
Yamaha YZ 2020 Series Owner'S Service Manual preview
YZ 2020 Series
Бренд: Yamaha Страницы: 376
Yamaha YZ125(P)/LC Owner'S Service Manual preview
YZ125(P)/LC
Бренд: Yamaha Страницы: 564
Yamaha YZ 2016 Series Owner'S Service Manual preview
YZ 2016 Series
Бренд: Yamaha Страницы: 392
Yamaha YZ 2018 Series Owner'S Service Manual preview
YZ 2018 Series
Бренд: Yamaha Страницы: 402
Yamaha YZ250F(V) Owner'S Service Manual preview
YZ250F(V)
Бренд: Yamaha Страницы: 674
Yamaha YZ250(R)/LC Owner'S Service Manual preview
YZ250(R)/LC
Бренд: Yamaha Страницы: 586
Yamaha YZ125(R)/LC Owner'S Service Manual preview
YZ125(R)/LC
Бренд: Yamaha Страницы: 568

Бренды по названию

Популярные бренды

Загрузить еще бренды