APRILIA CAPONORD 1200 Скачать руководство пользователя страница 89

Страница: 89 / 439

disconnected, check that there is not voltage at the circuit ends: if there is voltage, restore the cable

harness.

Error code B0006 (INSIDE ERROR)

There is a fault in the instrument panel.

Troubleshooting

Replace the instrument panel.

Error code B0007 (INSUFFICIENT NUMBER OF MEMORISED KEYS)

The number of stored keys is less than two.

Dashboard

In case of doubts in operation of the engine revs indication, it is possible to connect the vehicle to the

diagnostics instrument and activate the engine revs indication choosing the function "Rpm indicator"

from the "Devices Activation" screen page (injector icon)

SELECTING kph - mph UNIT OF MEASUREMENT

•

Connect the diagnostics instrument to the Marelli (7SM) engine control unit and start a di-

agnostics session.

•

Go to the "adjustments" page and configure the vehicle.

•

Close the current diagnosis session.

•

Enter the instrument panel diagnosis and do a KEY OFF / KEY ON

•

Enter the instrument panel diagnosis and make sure the error is present.

•

To solve the error, go to the "adjustments" page and carry out a "Vehicle configuration reset".

•

Follow the instructions on the screen.

•

Delete the errors stored by the instrument panel.

Diagnosis

The instrument errors are detected by means of the diagnosis instrument. It is therefore necessary to

connect it to the vehicle.

Following are listed the errors generated by the instrument panel.

CONFIGURATION

Error code B0000 (CONFIGURATION ERROR)

Error cause

The configuration memorised in the instrument panel does not correspond to the one detected in the

vehicle where it is installed (e.g. configuration unit of measurement miles/kilometres).

Identification

Warning light on.

Troubleshooting

CAPONORD 1200

Electrical system

ELE SYS - 89

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды