APRILIA CAPONORD 1200 Скачать руководство пользователя

Страница: 371 / 439

BLEED SYSTEM AFTER BRAKE PUMP RE-

PLACEMENT

PRELIMINARY OPERATIONS

•

Install the new brake pump.

•

Connect the reservoir to the brake

pump.

•

Connect the brake pipe to the pump

line coupling.

•

Fill the reservoir with new DOT4 brake

fluid.

REGULAR BLEEDING SYSTEM

•

Connect the bleed bottle to the bleed

screw of the front brake calliper.

•

Operate the brake lever.

•

Open the bleed screw until all the pres-

sure has been release and then close

it.

•

Release the brake lever.

•

After releasing the lever, wait two sec-

onds so that the brake fluid flows into

the cylinder.

•

Repeat this procedure until the brake

fluid is clear and has no air bubbles.

(about 10 to 20 times).

NOTE: CHECK BRAKE FLUID LEVEL IN THE

RESERVOIR AND, IF NECESSARY, TOP UP

(CHECKING BRAKE PAD WEAR).

•

Bleed as previously described, also on

the bleed valve installed on the front

brake pump.

•

Then perform the same procedure for

the rear brake calliper, acting only on

the valve installed on that calliper.

•

Fill the reservoir until it reaches the ref-

erence "MAX" and refit the cap (check

pad wear).

CAPONORD 1200

Braking system

BRAK SYS - 371

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды