APRILIA CAPONORD 1200 Скачать руководство пользователя страница 168

Страница: 168 / 439

between PIN 5 valve - PIN L2 VCU. If the cable harness is not damaged, replace the com-

ponent.

Error potentiometer exhaust valve shortcircuit C1707

Error cause

•

An excessive or null tension has been detected on PIN B4 VCU.

Troubleshooting

•

Disconnect the connector of the component and check its insulation from ground and supply

system of PIN 2: if the insulation is not present, restore the cabling, otherwise replace the

component.

Error potentiometer exhaust valve open circuit C1708

Error cause

•

An interruption of the circuit has been detected.

Troubleshooting

•

Check the connector on the component and the VCU connector. Disconnect the two con-

nectors and check the continuity of the cable between PIN 2 potentiometer and PIN B4 VCU

and restore the cable harness. If the cable harness is not damaged, replace the component.

Cruise Control Button

(IF APPLICABLE)

Function

Cruise Control is an electronic system that makes

it possible to set the desired speed and keep it

constant also in case of driving uphill or downhill,

without using the gas control.

The system is deactivated automatically when the

rider uses any of the brake/clutch controls or

Cruise Control button. It is very useful during long

motorway journeys, because it helps saving fuel

and makes riding less tiring.

Operation / Operating principle

To activate the function (switching from OFF to

ON), press and hold the Cruise Control button on

the handlebar for approximately 2 seconds: the

warning light on the instrument panel flashes to

indicate the ON status of the Cruise Control. The

set speed must be within the thresholds below:

Electrical system

CAPONORD 1200

ELE SYS - 168

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды