APRILIA CAPONORD 1200 Скачать руководство пользователя

Страница: 373 / 439

tective caps of the braking circuit un-

ions and connect the respective pipes.

Once all the braking circuits have been con-

nected, remove the protective caps from the

braking pump unions and connect the braking

pump pipes to the ABS control unit.

•

Unlock the lever and the brake pedal.

•

Remove the cap of the reservoir and fill

it with the new DOT 4 brake fluid up to

the reference "MAX".

•

Reinstall the cap.

CAUTION

PERFORM THE REGULAR BRAKING SYSTEM BLEED, AS
DESCRIBED AT THE BEGINNING OF THE CHAPTER.

•

Check the stroke and the sensitivity of both the lever and the brake pedal.

•

If, after bleeding, the pedal or the lever stroke is too long, check that there are no leaks in

the braking system and if everything is OK, continue bleeding operations using the diag-

nostics instrument as described.

•

Detach the bleed hoses and close the bleed screws again to the correct tightening torque.

BRAKE BLEEDING AFTER CALLIPER RE-

PLACEMENT

VEHICLE PREPARATION - The operations are

described for the front system, but they are al-

so valid for both braking systems.

•

Connect the bleed bottles to the bleed

screw of the front calliper and open it.

•

Fully press down the brake lever and

fasten it into position with a locking de-

vice so as to avoid fluid flowing out from

the open system.

•

Close the bleed screws of the front cal-

liper and remove the bleed bottle.

•

Replace the damaged calliper with a

new one.

•

Unlock the brake lever.

CAPONORD 1200

Braking system

BRAK SYS - 373

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды