APRILIA CAPONORD 1200 Скачать руководство пользователя | Manualshive

Страница: 189 / 439

background image

•

Communication speed: messages travel at a speed of 250 kbps (data arrive at nodes every

20 ms, i.e. 50 times/second).

CAN PROTOCOL (CONT. NETWORK AREA)

The communication protocol is CSMA/CD (Carrier Sense Multiple Access w/ Collision Detection).

In order to transmit, every nod must first check that the BUS (the connection among all devices) is free

before attempting to send a message with BUS (Carrier Sense).

If during this period there is no activity on BUS, every nod has the same chance to send a message

(Multiple Access). If two nodes start transmitting simultaneously, the nodes recognise the "colli-

sion" (Collision Detection) and initiate an exchange action based on message priority (messages remain

unaltered during exchange and there is no delay for high priority messages).

CAN protocol is based on messages and not on addresses. The message itself is divided into several

parts (frames), each of which has a meaning: message priority, data contained, error detection, recep-

tion confirmation, etc.

Every network nod receives all the messages sent through the BUS (with reception confirmation or error

messages) and each nod decides if the message is to be processed or rejected. Besides, every nod

can request information from the other nodes (RTR = Remote Transmit Request).

Level in electrical circuit diagram:

CAN line

Electrical specifications:

•

between PIN 66 and 80 of the control unit: approximately 130 Ohm

•

between PIN 26 and 27 of the instrument panel: approximately 120 Ohm

Pin out:

•

Line L: Orange cable between Marelli control unit PIN 66 and the black-bodied connector

PIN 27 of the instrument panel.

•

Line H: White/Black cable between Marelli control unit PIN 80 and the black-bodied con-

nector PIN 26 of the instrument panel.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

DIAGNOSTICS INSTRUMENT: ELECTRICAL ERRORS

CAN line "Mute Node" U1601

•

Mute Node.

Error cause

•

The injection ECU cannot send CAN signals; it receives signals from the instrument panel

and the ABS control unit (if any): the control unit may need replacing.

Troubleshooting

CAPONORD 1200

Electrical system

ELE SYS - 189

«
...
187
188
189
190
191
...
»

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CAPONORD 1200

Бренд: Sachs Bikes Страницы: 83

Бренд: PUIG Страницы: 6

Spyder RT Series

Бренд: Can-Am Страницы: 52

Бренд: KTM Страницы: 26

Бренд: Kabuto Страницы: 6

GM STAR 250 1986

Бренд: Maico Страницы: 32

Бренд: Salewa Страницы: 17

Бренд: Qingqi Страницы: 48

Бренд: Yadea Страницы: 100

Fastway PMB-01-5203

Бренд: Pro Moto Billet Страницы: 2

Бренд: Yamaha Страницы: 164

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 80

Бренд: DYNATEK Страницы: 3

Бренд: DYNATEK Страницы: 6

Бренд: DYNATEK Страницы: 12

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды