APRILIA CAPONORD 1200 Скачать руководство пользователя страница 208

Страница: 208 / 439

•

Working on the right side, insert the

three bolts with their washers.

•

Working on the right side, place the

spacers on the three bolts between the

engine block and the chassis.

CAUTION

THE SPACERS HAVE DIFFERENT SIZES. REFIT THEM IN
THE SAME WAY THEY WERE BEFORE BEING REMOVED.

•

Working from the left side, tighten the

three nuts.

•

Release the engine from the belt and

the hoist.

•

Refit the pinion and restore the gearing

chain clearance.

•

Reconnect the electric connections

and clamp the cable harnesses.

•

Carry out the vehicle preparation oper-

ations but in reverse order, restore the

correct level of all fluids and carry out

the adjustments that may be required.

Engine from vehicle

CAPONORD 1200

ENG VE - 208

Содержание CAPONORD 1200
























































































































































































































































































































































































































































Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды

APRILIA CAPONORD 1200, Руководство по обслуживанию станции

Результаты поиска

Содержание CAPONORD 1200

Отзывы:

Похожие инструкции для CAPONORD 1200

Бренды по названию

Популярные бренды